Copy Link
Add to Bookmark
Report
Soldiers of Death Issue 08 part 2
- How To Make a Shutgun - By TPP -
So how many of you have always wanted a gun but wasn't old enough or the
gun laws skrewed you. Well anyway, this file will tell you how to build your
own shotgun.
You will Need:
Amount
3/4in. Steel pipe | 18in | The barrel
2x4 | 18in | The stock
Superglue or Duct Tape | |
Sheet Metal | | Get strong as possible, no copper
| | or aluminum
Rubber bands | 1 |
Small Nails | 3 |
latch | 1 |
Hinges | 2 |
1/2in dowel | 1in |
1. Saw the 2x4 into two peice, one 8in and one 10 inches long. Drill a 3/4in
semicircle in the middle of the 2in side of the 8in 2x4, so the pipe fits in
the wood. Make sure the pipe is ok inside(no Little shavings).
2. Now Superglue the Pipe in the groove in the wood. Make sure the end of the
pipe lines up with one of the ends on the wood. You can duct tape it together
instead of using superglue. To be safe, use both.
3. Now take the other peice of wood and carve the handle in.. sorta like this
_______________________
| |
| ____ |
|________________/ |__|
4. Now, Take your sheet metal and cut out a trigger design. Make it like this.
Punch a hole in the back of the trigger when done.
___
| | - It must have a thing like this coming out of the top of it.
| |
| |___
Put --|o |
| /
| | --- Your trigger design
|___/
5. Put the two together like if it were two peices of a shotgun. Put a 12
guage shell in the pipe and mark on the 10in length were the shell primer
touched the wood.
6. Drill a 1/2in diameter hole in the side with the mark. Make sure the center
of the drill touches the primer mark. Drill about 4 in deep. Now saw down the
middle toward the end that has the cut out till the drilled hole stops.
7. Get a 1/2in diameter dowl and cut off a 1in length of it. Now, Shave off a
little wood from it so it is just small enough to slide down the hole you made
in the wood. Take it out and pound a small nail though the exact center of one
of the circular sides of the dowel. Like this...
_______ Nail
dowel | |_______ /
\ |_____|
8. Cut a small notch in the middle of the botumn of the dowel. Now superglue
the trigger into the notch like this.
___________ /Dowel Nail
| |_____________/
|_________|
| |\_Notch
| |___
|o |
| / -Trigger
| |
|___/
9. Now put this in the hole you made so the nail faces the opening. Get a
small peice of wood or liquid wood and block up the cut that the trigger top
is in.
10. Now, get some cheap hinges and skrew them on the wood perfectly so the
barrel lines up with the hole you made.
11. Get a cheap latch. Attach this to one side at the top of the gun.
Put some small small nails in each side of the shotgun four inches in front
of where the barrel connects with the hole. Now, take a rubberband, attach
it to one of the nails, move it through the hole in the back of the trigger,
and connect it to the other nail.
NoTE- Make sure the trigger is as far to the front as possible.
12. Now, you can cut it up into whatever shape you like..
To Fire- Pull The trigger back and let go.
To Load- Undo the latch, drop out the shell and put another bullet in. I have
seen some latches where you can just pull the front part down, no little
shitty hook.
Note- You should always test your gun before first using it. Go to a deserted
area, like way out in the woods. Tie the gun to a tree or a peice of wood. Set
up a target in front of it. Tie a string to the trigger, stand away and pull
back. If the gun dosen't fuck up, you can use it.
