Copy Link
Add to Bookmark
Report
Commodore Hacking Issue 03
########
##################
###### ######
#####
##### #### #### ## ##### #### #### #### #### #### #####
##### ## ## #### ## ## ## ### ## #### ## ## ##
##### ######## ## ## ## ##### ## ## ## ## ##
##### ## ## ######## ## ## ## ### ## ## #### ## ##
##### #### #### #### #### ##### #### #### #### #### #### ######
##### ##
###### ###### Volume 1 - Issue 3
################## July 15, 1992
########
=============================================================================
Editor's Notes:
by Craig Taylor (duck@pembvax1.pembroke.edu)
Here's over 3000 lines of hacking articles & such... Sorry about the length
as some of the articles ran a bit overboard. Included within is a discussion of
the KERNAL routines, an examination of Rasters, and a package of burst routines
for use in your own programs. If you've got any ideas for articles etc that
you'd like to see or want to hear more on a certain topic feel free to email
me.
I'm pleased to introduce the Demo Corner where each month we'll report
how to achieve some of the graphic and sound effects that are present in
many demos that are wondered about.
Note: The article concerning programming and usage of the 1351 mouse has
been delayed until the next issue due to time and length constraints.
This file is available via anonymous ftp at tybalt.caltech.edu under
pub/rknop/hacking.mag. Back issues of C= Hacking are also located there.
**************** WARNINGS, UPDATES, BUG REPORTS, ETC... **********************
OOPS - In the last issue of C= Hacking in Mark Lawrence's File Splitter a line
inadvertantly got chopped off. The following code should be fixed between the
comments that are listed:
[.
.
.]
{ Make EXTENSION a string representation of COUNT, to be added to the
OutFileName to make things a tad easier}
OutFileName := Concat(NewFile,'.',Copy('00',1,3-Length(Extension)),
Extension); {**THIS IS THE STATEMENT...**}
{ Create filename based on which part we're up to }
[.
.
.]
=============================================================================
Note: Permission is granted to re-distribute this "net-magazine", in whole,
freely for non-profit use. However, please contact individual authors for
permission to publish or re-distribute articles seperately.
*** AUTHORS LISTED BELOW RETAIN ALL RIGHTS TO THEIR ARTICLES ***
=============================================================================
In This Issue:
Learning ML - Part 3
In this edition we take a look at reading and writing commands to the disk
drive, including reading the disk directory and error channel. This article
parallels the discussion of the C=128 and C=64 KERNAL jump tables of available
routines. Written by Craig Taylor.
The Demo Corner: Missing Cycles
Everybody knows that there are 63 cycles available to the C64 processor
on each scan line, except for one which only provides 23 cycles. But what
happens when we add sprites and why ? Written by Pasi 'Albert' Ojala.
KERNAL 64/128
The C=128 and C=64 jump table points to many valuable system routines is
discussed and examined in detail. Written by Craig Taylor.
64K VDC RAM and an alternate GEOS128 Background Screen
Standard GEOS only uses the first 16K of your VDC screen. If you have 64K
of VDC RAM, and want to write an 80-column only application, you can put some
of the additional VDC RAM to use as a replacement for the standard GEOS
background screen. And, in the bargain, you get an additional 16K of
application FrontRAM to use! Written by Robert Knop.
GeoPaint File Format
Written by Bruce Vrieling, this article provides an in depth description of
exactly how geoPaint stores its graphic images on disk. It examines the
concept of VLIR files, how graphics data is laid out on screen (from both
geoPaint and the VIC's perspective), and geoPaint's graphics compression
techniques.
Rasters - What They Are and How to Use Them
Written by Bruce Vrieling, this article provides an introduction to creating
special on-screen effects using the technique of raster interrupts. The
basics are examined, including what they are, and how to program them. This
article should provide a good starting point for someone wanting to get
their feet wet in raster programming.
Bursting Your 128: The Fastload Burst Command
Written by Craig Bruce this article covers the Fastload burst command of the
1571 and 1581 disk drives. The Fastload command operation and protocol are
discussed and a package for using the Fastload command to read regular
sequential files at binary program loading speeds is presented. To demonstrate
the package, a file word counting utility is implemented and the "commented"
code is included.
============================================================================
Learning ML - Part 3
by Craig Taylor (duck@pembvax1.pembroke.edu)
Last time we used a routine at $FFD2 which would print out the character code
contained within the accumalator. That location will always print the character
out regardless of VIC-20, C=64, C=128 and even PET because Commodore decided
to set up some locations in high memory that would perform routines that are
commonly needed.
Take a look now at the KERNAL 64/128 article and glance over some of the
routines and their function / purpose. This article is meant to be a companion
to that article so you may want to flip back and forth as the discussion
of the program listed below is discussed.
Note that I've borrowed Craig Bruce's notation of having listings inside. To
extract the source that follows enter the following command on a Unix system:
grep '^\.@...\!' Hack3 | sed 's/^.@...\!.//' | sed 's/.@...\!//' >dir.asm
.@001! ;
.@002! ; Set up computer type for computer-dependant code /
.@003! ; Only used in displaying # routine / start of assembly setting.
.@004! ; BUDDY format.
.@005! ;
.@006! computer = 128 ; Define as either 64 or 128.
For both c64 and c128 users the following code works. Within the code is
conditional assembly which means it will work on either computer assuming that
the computer is equal to either 128 or 64.
.@007!
.@008! .if computer-64 ;** if computer not c64 then
.@009! .org $1300 ; and also make sure in BANK 15 when calling
.@010! ; these routines.
.@011! .else ;** else if _is_ c64, then
.@012! .org $c000
.@013! .ife ;** end of computer-dependant code.
Because of this (the source is in BUDDY format) the C64 and C128 are set to
assemble at different memory locations. On the C64, $c000 is 49152. On the C128
it is at 4864. Note for the C128 it is necessary to do a BANK15 before executing
the code.
.@014! .mem ; - assemble to memory.
This tells the assembler to actually put the code into memory.
.@015!
.@016! ;;-----------------------------------------------------------------------
.@017! ;; KERNAL EQUATES
.@018! ;;---------------------------------------------------------------------
.@019!
.@020! setnam = $ffbd
.@021! setlfs = $ffba
.@022! open = $ffc0
.@023! close = $ffc3
.@024! chkin = $ffc6
.@025! chrin = $ffcf
.@026! bsout = $ffd2
.@027! clrch = $ffcc
.@028!
These are the KERNAL routines we will actually be using. Their actual
use will be documented when we come across them within the code.
.@029! ;;-----------------------------------------------------------------------
.@030!
.@031! temp = 253
.@032! charret = $0d
.@033! space = $20
.@034!
Temp is set up to just be a temporary location in zero-page. Location 253 on
both the C64 and C128 is unused. Charret stands for the carriage return
character and is the equivlent of a chr$(13). Space stands for the code for a
space (a chr$(32))
.@035! ;;---------------------------------------------------------------------
.@036!
.@037! start = *
.@038!
.@039! jsr read'dir ; Initial jump table -- Note: Will read error after
.@040! jmp read'err ; showing directory.
.@041!
You'll see code like this a lot -- Basically we're building what is known as a
jump table. That way if we add more code to the directory or error routine we
don't have to worry about our SYS call's changing. To read the directory just
SYS base, to read the error channel just SYS base+3 (where BASE is 49152 on the
C64, 4864 on the 128)...
Also the JSR JMP combination may seem a little strange but what we are doing
is treating the directory routine as a subroutine and then JUMPING to the
error routine. Once we do that the RTS in read'err will return us back to basic.
.@042! ;;----------------------------------------------------------------------
.@043!
.@044! read'dir = *
.@045!
.@046! ; Opens and reads directory as a basic program.
.@047! ;==
.@048! ; Basic programs are read in as follows:
.@049! ; [Ptr to Next Line]:2 [Line #]:2 [Text]:.... [$00 byte]
.@050! ; ^^^^^^^^^^^REPEATS^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
.@051! ; The end of a program is signifed by the $00 byte signifying end of text
.@052! ; and the ptr's also being = $00.
.@053! ;==
There are several ways to read the directory in machine language. What we are
doing here is taking advantage of the drive's ability to allow us to load the
directory as a basic program -*except*- we aren't loading it per se. We're
gonna grab each byte as it comes from the drive and interpret it ourselves
instead of putting it in memory as would normally be done.
Basic programs are stored as the following: A 2 byte pointer, a 2 byte
line #, the basic text, and a null terminator and then starting over
from the 2 byte pointer. The pointer we do not need, the line # is the number
of blocks the file takes up and the TEXT is the program name and file type. We
know when we're finished on the line by checking for a $00 byte.
.@054! ; Begin by opening up the
.@055! ; directory file ("$").
.@056! lda #$01 ; length is 1
.@057! ldx #<dir ; lo byte pointer to file name.
.@058! ldy #>dir ; hi byte pointer to file name.
.@059! jsr setnam ; - call setnam
Okay, first we need to simulate opening the directory as a program file.
SETNAM sets up the filename for the open command. In effect we are giving the
basic syntax of open file#,device#,channel#,"filename" in reverse.
.@060! lda #$01 ; file # 1
.@061! ldx #$08 ; device # 8
.@062! ldy #$00 ; channel # 0
.@063! jsr setlfs ; - call setlfs
Here we specify the device #, file #, channel # in preperation for the open.
.@064! jsr open ; - call open
Open up the file. This is the routine that does the real work. SETNAM and
SETLFS were preparatory routines for this.
.@065! ;
.@066! ; read in the bytes and display (skipping line links etc)
.@067! ;
.@068! ldx #$01 ; file #1
.@069! jsr chkin ; - call chkin to set input file #.
Now we need to specify the input file # and tell the computer that all further
chrin's are to be from file #1. (By default, it would have read from the
keyboard unless we had this here).
.@070! jsr chrin ; - ignore starting address (2 bytes)
.@071! jsr chrin
Skip the starting address -- When reading the directory it is not relevant
so read the bytes and discard them.
.@072! skip jsr chrin ; - ignore pointer to next line (2 bytes)
Now we skip the pointer for the next line. This is only used when loading
basic programs to re-link the lines. When listing the directory they are not
needed.
.@073! bck1 jsr chrin
This is still part of the routine that skips the pointer to the next line, yet
it has a label used below that allows us to check for end of file more easily.
.@074! line jsr chrin ; - get line # lo.
.@075! sta temp ; - store lo of line # @ temp
.@076! jsr chrin ; - get hi of line #
Here we get the line # as the next 2 bytes in the file.
.@077!
.@078! .if computer-64 ; * if C128 then
Unfortunately C= did not provide a nice routine in the KERNAL to display
numeric values - however - by exploring inside the operating system a way to
display numbers is there. Note that the following may look confusing -- if it
does just rest assured it will print out the line # correctly.
.@079! sta $61
.@080! ldy temp
.@081! sty $60
.@082! lda #$00
.@083! sta $63
.@084! ldy temp ; store values for conversion.
.@085! jsr $ba07 ; - MONITOR routine: convert to BCD values
.@086! lda #$00
.@087! ldx #$08
.@088! ldy #$03
.@089! jsr $ba5d ; - MONITOR routine: print BCD
.@090! ;values in decimal
This is the C128 version which uses some of the MONITOR routines to display
the numeric block size.
.@091! .else ; * else if c64
.@092! ldx temp
.@093! jsr $bdcd ; - print line # (w/in ROM routine).
.@094! .ife ; * end of computer dependant code.
This is the C64 code to display a numeric value (notice how much simplified it
is over the C128)...
.@095!
.@096! lda #space
.@097! jsr bsout ; - print space
Let's print a space between the filename and the block size.
.@098! gtasc jsr chrin ; - start printing filename until
.@099! ;end of line.
.@100! beq chck ; (Zero signifies eol).
.@101! jsr bsout ; - Print character
.@102! sec
.@103! bcs gtasc ; and jump back.
Now we start getting a character (line #98), if zero we branch out of the loop
(line #100), else we display the character (#101), and jump back (#102-03).
.@104! chck lda #charret ; - Else we need to start the next line
.@105! jsr bsout ; Print a carriage return.
Ah, we got to a null byte so that's the end of this line - display a car/ret.
.@106! jsr chrin ; - And get the next pointer
.@107! bne bck1 ; If non-zero go, strip other ptr,
.@108! ; and continue.
This is where we branch back -- we are checking here for 2 null bytes on
input. We get the first byte of the pointer and if it's non-zero then we know
it's not the end of the directory so we jump back to discard the second byte at
line #73.
.@109! jsr chrin ; - Else check 2nd byte of pointer
.@110! bne line ; as if both 0 then = end of directory.
This is a continuation of the checking above. This time we're getting the
2nd byte and checking for 0. If it's not we jump back to get and display the
line # etc. If it is 0 then that means we had $0000 for the next pointer which
means that it's the end of the directory.
.@111! ;
.@112! ;had 3 0's in a row so end of prog
.@113! ;now close the file.
.@114! ;
.@115! lda #$01 ; file # to close
.@116! jsr close ; - so close it
.@117! jsr clrch ; - clear all channels
.@118! rts ; - and return to basic
.@119!
We then close the file by specifying the file # and calling close. We then
tell the computer to reset all the default input / output devices by calling
clrch (remember we changed the default input channel??). And then we can return
to where this routine was called from.
.@120! ; FILENAME string
.@121! dir .asc "$"
This is the string that is pointed to by the SETNAM call. Note that a search
pattern could be set by
line#121: .asc "$hack*"
and by changing the length set in .A in the call in line #56.
.@122!
.@123! ;;-----------------------------------------------------------------------
.@124!
.@125! read'err = *
.@126!
.@127! ; This routine simply grabs bytes from a channel 15 it opens up until
.@128! ; a car/ret byte is found. Then it closes and returns.
.@129!
Reading the error channel is much much more simpler than reading the
directory. Basically we just open up the channel (specifying a null name) and
repeatadly get bytes until a car/ret is found.
.@130! rderr lda #$00 ; length is 0
.@131! jsr setnam ; - call setname
Setup so we don't specify a name (length = 0).
.@132! lda #$0f ; file # (15)
.@133! ldx #$08 ; device # (08)
.@134! ldy #$0f ; channel # (15)
.@135! jsr setlfs ; - set logical file #
Do the equivlent of open 15,8,15.
.@136! jsr open ; - and open it.
Open it.
.@137! ;specify file as input
.@138! ldx #$0f ; file 15 is input
.@139! jsr chkin ; - so specify it.
Now set up file # 15 as input so we can start getting, displaying etc until
a car/ret is found.
.@140! ;now read in file
.@141! loop jsr chrin ; - read char
.@142! jsr bsout ; - print char
.@143! cmp #charret ; is it return?
.@144! bne loop ; - if not jmp back
Read in and display the characters from the error channel until a char/ret is
found.
.@145! ;now close the file
.@146! lda #$0f ; file #
.@147! jsr close ; - close the file
.@148! jsr clrch ; restore i/o
And once it is, we close the file and restore the default i/o settings.
.@149! ;now return to basic
.@150! rts
And return to our caller, in this case - basic.
============================================================================
[ The Demo Corner is going to be a column where each month we'll be
introduced to a new feature (some people call them bugs, we'll call them
features) of the Commodore 64 or 128 in the Video and Sound areas that
have commonly been shown on demos but with no mention of how to accomplish
them. Note that readers may also want to take a look at the introduction
to Rasters elsewhere in this magazine.]
The Demo Corner: Missing Cycles
by Pasi 'Albert' Ojala (po87553@cs.tut.fi albert@cc.tut.fi)
Written on 15-May-91 Translation 30-May-92
Missing Cycles
--------------
[all timings are in PAL, the principle applies to NTSC too]
Everybody knows that there are 63 cycles available to the C64 processor on
each scan line, except for one which only provides 23 cycles (later referred
to as a "bad" scan line). But what happens when we add sprites and why ?
In the C64, the VIC (video interface controller) has much more to do than
just showing graphics on the screen. It also handles the memory refresh.
On each scanline, it has to refresh five rows in the memory matrix and
fetch fourty bytes of graphics data.
The VIC does all of this during the cycles (phase 1) that the processor is
not using the memory. These cycles, however, are not sufficient when the
VIC also needs to access the character and color codes for the next row.
The memory bus can't be used by the CPU and the VIC at the same time, so CPU
access to the bus must be denied to allow the VIC to fetch its data.
Fortunately, the VIC bus (12-bit wide) allows the character (8 bits) and
color (4 bits) codes to be fetched at the same time.
_Understanding how sprites work_
If there are sprites on the screen, the VIC needs even more cycles to fetch
all of the graphics data. Scan lines are time divided so that there is
enough time for all action during one line. On each line, the sprite
image pointers are fetched during phase 1. If the sprite is to be displayed
on that line, the three bytes of image data are fetched right after that.
Out of these three fetches, two take place during phase 2 of the clock,
so the processor will lose these. On average, two clock cycles are lost
for each sprite that is displayed on that line.
But how is it possible for all eight sprites to only take 16-19 cycles
(depending on the timing) when we have observed that one sprite requires
three cycles? And why do sprites 0, 2, 4, 6 and 7 together take up as many
cycles as all eight sprites ? The answer may be found in the way the VIC
tells the CPU that it needs additional cycles.
_The BA signal_
When the VIC wants to use the bus, the BA (Bus Available) signal goes
inactive. This will happen three cycles before the bus must be released !
During these three cycles, the CPU must complete all memory accesses or
delay them until it has the bus again.
The CPU either completes the current instruction in the remaining cycles
or sits and waits for the bus to become available again. It can't execute
a new instruction as long as it doesn't have the bus. This is why cycles
seem to be lost (besides those stolen directly for the sprites). Usually,
all 8 sprites take 17 cycles while one sprite takes three cycles. However,
the CPU may continue to execute an instruction if it does not use the bus.
_Theory and speculation_
Let's suppose that all the sprites are enabled and on the same scan line.
Then, the VIC steals 16 cycles (2 cycles for each sprite) for the memory
fetches and 3 cycles as overhead for the BA signal, for a total of 19 cycles.
However, it will be usually less because the CPU will use some of the cycles
when the bus request is pending.
If we now disable sprite 4, no cycles are released for the CPU's use. This
is because during the previous sprite 4 data fetch, the VIC already signals
that it needs the bus for the sprite 5 data fetch and BA stays low (Refer
to the timing chart). Thus, the CPU never sees BA go high during sprite 4
and 2 cycles are still lost.
Accordingly, if we only turn off sprites 1, 3 and 5 we get no cycles back
from the VIC. So in time-critical raster routines, always use sprites in
order.
_What can we do with this feature ?_
How can this be useful? A good use is for synchronization. Normally,
before the CPU starts to execute the raster interrupt code, it's executing
an instruction of undefined cycle-length. This execution time varies from
two to seven cycles.
With a sprite, you can do the synchronization with a minimal effort using
a DEC or INC instruction in the right place. If the processor is early,
it has to wait for the bus, otherwise it will continue to execute cycles
from the instruction.
I have never experimented with any other instruction than DEC/INC, but
some others should work also. You need an instruction which has a cycle that
do not need the bus to be available. e.g. INC $3fff will increase the
value during the fifth cycle and do not need the bus for that.
_A demo program_
The enclosed program includes a short raster color routine to demonstrate
this strict timing and synchronization. The background color is changed
12 times on each line. The electron beam runs over eight pixels during
one cycle, so the timing must be precise.
--------------------------------------------------------------------------
_Table for PAL VIC timing for the Missing cycles_
012345678901234567890123456789012345678901234567890123456789012 cycles
Normal scan line, 0 sprites
ggggggggggggggggggggggggggggggggggggggggrrrrr p p p p p p p p phi-1 VIC
phi-2 VIC
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx phi-2 6510
63 cycles available
Normal scan line, 8 sprites
ggggggggggggggggggggggggggggggggggggggggrrrrr pspspspspspspsps phi-1 VIC
ssssssssssssssss phi-2 VIC
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxXXX phi-2 6510
46-49 cycles available
Normal scan line, 4 sprites
ggggggggggggggggggggggggggggggggggggggggrrrrr psp psp psp psp phi-1 VIC
ss ss ss ss phi-2 VIC
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxXXX xx phi-2 6510
48-51 cycles available
Bad scan line, 0 sprites
ggggggggggggggggggggggggggggggggggggggggrrrrr p p p p p p p p phi-1 VIC
cccccccccccccccccccccccccccccccccccccccc phi-2 VIC
xxxxxxxxxxxxxxxxxxxxxxx phi-2 6510
23 cycles available
Bad scan line, 8 sprites
ggggggggggggggggggggggggggggggggggggggggrrrrr pspspspspspspsps phi-1 VIC
cccccccccccccccccccccccccccccccccccccccc ssssssssssssssss phi-2 VIC
xxxxXXX phi-2 6510
4-7 cycles available
g= grafix data fetch (character images or graphics data)
r= refresh
p= sprite image pointer fetch
c= character and color CODE fetch during a bad scan line
s= sprite data fetch
x= processor executing instructions
X= processor executing an instruction, bus request pending
Observe! The left edge of the chart is not the left edge of the screen nor
the left edge of the beam, but the sprite x-coordinate 0. If you
have opened the borders, you know what I mean. A sprite can be
moved left from the coordinate 0 by using x-values greater than 500.
___________
| _______ |<-- Maximum sized video screen
||| | |
||| |<-- Normal C64 screen
||| | |
|||_______| |
|| |
||__________|
^ Sprite coordinate 0
--------------------------------------------------------------------------
Demonstration program for missing cycles
COLOR0= $CE00 ; Place for color bar 0
COLOR1= $CF00 ; Place for color bar 1
RASTER= $FA ; Line for the raster interrupt
DUMMY= $CFFF ; Timing variable
*= $C000
SEI ; Disable interrupts
LDA #$7F ; Disable timer interrupts
STA $DC0D
LDA #$01 ; Enable raster interrupts
STA $D01A
STA $D015 ; Enable Sprite 0
LDA #<IRQ ; Init interrupt vector
STA $0314
LDA #>IRQ
STA $0315
LDA #$1B
STA $D011
LDA #RASTER ; Set interrupt position (inc. 9th bit)
STA $D012
LDA #RASTER-20 ; Sprite will just reach the interrupt position
STA $D001 ; when it is positioned 20 lines earlier
LDX #51
LDY #0
STA $D017 ; No Y-enlargement
LOOP0 LDA COL,X ; Create color bars
PHA
AND #15
STA COLOR0,X
STA COLOR0+52,Y
STA COLOR0+104,X
STA COLOR0+156,Y
PLA
LSR
LSR
LSR
LSR
STA COLOR1,X
STA COLOR1+52,Y
STA COLOR1+104,X
STA COLOR1+156,Y
INY
DEX
BPL LOOP0
CLI ; Enable interrupts
RTS ; Return
IRQ NOP ; Wait a bit
NOP
NOP
NOP
LDY #103 ; 104 lines of colors (some of them not visible)
; Reduce for NTSC, 55 ?
INC DUMMY ; Handles the synchronization with the help of the
DEC DUMMY ; sprite and the 6-clock instructions
; Add a NOP for NTSC
FIRST LDX COLOR0,Y ; Do the color effects
SECOND LDA COLOR1,Y
STA $D020
STX $D020
STA $D020
STX $D020
STA $D020
STX $D020
STA $D020
STX $D020
STA $D020
STX $D020
STA $D020
STX $D020
; Add a NOP for NTSC (one line = 65 cycles)
LDA #0 ; Throw away 2 cycles (total loop = 63 cycles)
DEY
BPL FIRST ; Loop for 104 lines
STA $D020
LDA #103 ; For subtraction
DEC FIRST+1 ; Move the bars
BPL OVER
STA FIRST+1
OVER SEC
SBC FIRST+1
STA SECOND+1
LDA #1 ; Ack the raster interrupt
STA $D019
JMP $EA31 ; Jump to the standard irq handler
COL BYT $09,$90,$09,$9B,$00,$99,$2B,$08,$90,$29,$8B,$08,$9C,$20,$89,$AB
BYT $08,$9C,$2F,$80,$A9,$FB,$08,$9C,$2F,$87,$A0,$F9,$7B,$18,$0C,$6F
BYT $07,$61,$40,$09,$6B,$48,$EC,$0F,$67,$41,$E1,$30,$09,$6B,$48,$EC
BYT $3F,$77,$11,$11
; Two color bars
--------------------------------------------------------------------------
Basic loader for Missing cycles example program (PAL)
1 S=49152
2 DEFFNH(C)=C-48+7*(C>64)
3 CH=0:READA$,A:PRINTA$:IFA$="END"THENPRINT"<clr>":SYS49152:END
4 FORF=0TO31:Q=FNH(ASC(MID$(A$,F*2+1)))*16+FNH(ASC(MID$(A$,F*2+2)))
5 CH=CH+Q:POKES,Q:S=S+1:NEXT:IFCH=ATHEN3
6 PRINT"CHECKSUM ERROR":END
100 DATA 78A97F8D0DDCA9018D1AD08D15D0A9578D1403A9C08D1503A91B8D11D0A9FA8D, 3773
101 DATA 12D0A9E68D01D0A233A0008D17D0BDACC048290F9D00CE9934CE9D68CE999CCE, 4157
102 DATA 684A4A4A4A9D00CF9934CF9D68CF999CCFC8CA10D95860EAEAEAEAA067EEFFCF, 4878
103 DATA CEFFCFBE18CEB94FCF8D20D08E20D08D20D08E20D08D20D08E20D08D20D08E20, 4403
104 DATA D08D20D08E20D08D20D08E20D0A9008810D18D20D0A967CE64C010038D64C038, 3923
105 DATA ED64C08D67C0EE19D04C31EA0990099B00992B0890298B089C2089AB089C2F80, 3483
106 DATA A9FB089C2F87A0F97B180C6F076140096B48EC0F6741E130096B48EC3F771111, 3133
200 DATA END,0
--------------------------------------------------------------------------
Uuencoded C64 executable version (PAL)
begin 644 missing.64
M`0@-"`$`4[(T.3$U,@`F"`(`EJ5(*$,ILD.K-#BJ-ZPH0[$V-"D`40@#`$-(?
MLC`ZAT$D+$$ZF4$D.HM!)+(B14Y$(J>9(I,B.IXT.3$U,CJ``(@(!`"!1K(P/
MI#,Q.E&RI4@HQBC**$$D+$:L,JHQ*2DIK#$VJJ5(*,8HRBA!)"Q&K#*J,BDI:
M*0"I"`4`0TBR0TBJ43J74RQ1.E.R4ZHQ.H(ZBT-(LD&G,P#!"`8`F2)#2$5#F
M2U-532!%4E)/4B(Z@``."60`@R`W.$$Y-T8X1#!$1$-!.3`Q.$0Q040P.$0QK
M-40P03DU-SA$,30P,T$Y0S`X1#$U,#-!.3%".$0Q,40P03E&03A$+"`S-S<SA
M`%L)90"#(#$R1#!!.44V.$0P,40P03(S,T$P,#`X1#$W1#!"1$%#0S`T.#(Y?
M,$8Y1#`P0T4Y.3,T0T4Y1#8X0T4Y.3E#0T4L(#0Q-3<`J`EF`(,@-C@T031!4
M-$$T03E$,#!#1CDY,S1#1CE$-CA#1CDY.4-#1D,X0T$Q,$0Y-3@V,$5!14%%>
M045!03`V-T5%1D9#1BP@-#@W.`#U"6<`@R!#149&0T9"13$X0T5".31&0T8X^
M1#(P1#`X13(P1#`X1#(P1#`X13(P1#`X1#(P1#`X13(P1#`X1#(P1#`X13(PH
M+"`T-#`S`$(*:`"#($0P.$0R,$0P.$4R,$0P.$0R,$0P.$4R,$0P03DP,#@XV
M,3!$,3A$,C!$,$$Y-C=#138T0S`Q,#`S.$0V-$,P,S@L(#,Y,C,`CPII`(,@^
M140V-$,P.$0V-T,P144Q.40P-$,S,45!,#DY,#`Y.4(P,#DY,D(P.#DP,CDX[
M0C`X.4,R,#@Y04(P.#E#,D8X,"P@,S0X,P#<"FH`@R!!.49",#@Y0S)&.#=!?
M,$8Y-T(Q.#!#-D8P-S8Q-#`P.39"-#A%0S!&-C<T,44Q,S`P.39"-#A%0S-&V
;-S<Q,3$Q+"`S,3,S`.@*R`"#($5.1"PP````8
``
end
size 747
--------------------------------------------------------------------------
Uuencoded C64 executable version (NTSC)
begin 644 missing.64
M`0@-"`$`4[(T.3$U,@`F"`(`EJ5(*$,ILD.K-#BJ-ZPH0[$V-"D`40@#`$-(?
MLC`ZAT$D+$$ZF4$D.HM!)+(B14Y$(J>9(I,B.IXT.3$U,CJ``(@(!`"!1K(P/
MI#,Q.E&RI4@HQBC**$$D+$:L,JHQ*2DIK#$VJJ5(*,8HRBA!)"Q&K#*J,BDI:
M*0"I"`4`0TBR0TBJ43J74RQ1.E.R4ZHQ.H(ZBT-(LD&G,P#!"`8`F2)#2$5#F
M2U-532!%4E)/4B(Z@``."60`@R`W.$$Y-T8X1#!$1$-!.3`Q.$0Q040P.$0QK
M-40P03DU-SA$,30P,T$Y0S`X1#$U,#-!.3%".$0Q,40P03E&03A$+"`S-S<SA
M`%L)90"#(#$R1#!!.44V.$0P,40P03(S,T$P,#`X1#$W1#!"1$%%0S`T.#(YA
M,$8Y1#`P0T4Y.3,T0T4Y1#8X0T4Y.3E#0T4L(#0Q-3D`J`EF`(,@-C@T031!6
M-$$T03E$,#!#1CDY,S1#1CE$-CA#1CDY.4-#1D,X0T$Q,$0Y-3@V,$5!14%%>
M045!03`S-T5%1D9#1BP@-#@S,`#U"6<`@R!#149&0T9%04)%,#!#14(Y,#!#4
M1CA$,C!$,#A%,C!$,#A$,C!$,#A%,C!$,#A$,C!$,#A%,C!$,#A$,C!$,#A%$
M+"`T-3`R`$(*:`"#(#(P1#`X1#(P1#`X13(P1#`X1#(P1#`X13(P1#!%04$Y.
M,#`X.#$P1#`X1#(P1#!!.38W0T4V-4,P,3`P,SA$-C4L(#,Y-#(`CPII`(,@R
M0S`S.$5$-C5#,#A$-CA#,$5%,3E$,#1#,S%%03`Y.3`P.3E",#`Y.3)",#@Y(
M,#(Y.$(P.#E#,C`X.4%",#@Y0RP@,S4U.`#<"FH`@R`R1C@P03E&0C`X.4,R_
M1C@W03!&.3=",3@P0S9&,#<V,30P,#DV0C0X14,P1C8W-#%%,3,P,#DV0C0XK
M14,S1C<W+"`S,C<T`"<+:P"#(#$Q,3$P,#`P,#`P,#`P,#`P,#`P,#`P,#`PO
M,#`P,#`P,#`P,#`P,#`P,#`P,#`P,#`P,#`P,#`P,#`P,#`P,#`L(#,T`#,+1
,;`"#($5.1"PP````"
``
end
size 822
============================================================================
Kernal 64 / 128
by Craig Taylor (duck@pembvax1.pembroke.edu)
+--------------+
| Introduction |
+--------------+
When Commodore introduced the PET ages ago before the Vic-20 and Commodore 64,
128 they set in the highest memory locations a series of jumps to other routines
so that users didn't need bother checking if any revisions had been made. They
were assured that the address they were jumping to, would indeed, be the address
that would print out a character or whatnot.
The KERNAL has grown since Commodore first introduced it, the C=128 KERNAL has
fifty-seven seperate routines which are available to programmers. These routines
handle functions relating to the serial devices (the bulk of them), the screen
and miscellanous system routines such as scanning the keyboard, updating and
reading the system clock (TI$).
+-------------------+
| Table of Routines |
+-------------------+
The following table lists the available routines, their function, address,
their name, and registers affected upon exit. In addation, on the left of each
line are the group that I have catagorized them under: Video(Vid), System(Sys),
and Serial(Ser).
--------+---------+---------+---------------------------------------+-----------
| |Registers| |Group
Address | NAME | A X Y F | Descritption |Vid Sys Ser
--------+---------+---------+---------------------------------------+-----------
FF47/128|SPINSPOUT| * | Initializes I/O for fast serial | ***
FF4A/128| CLOSEALL| * * * | Close all files on a device | ***
FF4D/128| C64MODE | | Switches to C=64 mode | ***
FF50/128| DMACALL | * * | Send DMA command to REU | ***
FF53/128| BOOTCALL| * * * | Attempts to run boot sector | *** ***
FF56/128| PHOENIX | * * * | Initalizes external/internal cartri. | ***
FF59/128| LKUPLA | * * * * | Looks up logical device # | *** ***
FF5C/128| LKUPSA | * * * * | Looks up for secondary address | *** ***
FF5F/128| SWAPPER | * * * | Switches betten 40 / 80 column screen |***
FF62/128| DLCHAR | * * * | Initializes 80 column character set |***
FF65/128| PFKEY | * * * * | Installs a function key definition | ***
FF68/128| SETBNK | | Sets bank for any I/O operations | *** ***
FF6B/128| GETCFG | * | Get MMU configuration for a given bank| ***
FF6E/128| JSRFAR | | Jumps to a subroutine in another bank | ***
FF71/128| JMPFAR | | Starts executing code in another bank | ***
FF74/128| INDFET | * * * | Execute a LDA(fetvec),Y from a bank | ***
FF77/128| INDSTA | * * | Stores a value indirectly in a bank | ***
FF7A/128| INDCMP | * * | Compares a value indirectly in a bank | ***
FF7D/128| PRIMM | | Outputs null-terminated string |*** ***
////////|/////////|/////////|///////////////////////////////////////|///////////
FF81 | CINT | * * * | Setup VIC,screen values, 8563... |***
FF84 | IOINIT | * * * | Initialize VIC,SID,8563,CIA for system|*** ***
FF87 | RAMTAS | * * * | Initialize ram. | ***
FF8D | VECTOR | * * | Reads or Writes to Kernal RAM Vectors | ***
FF90 | SETMSG | | Sets Kernal Messages On/Off. | ***
FF93 | SECND | * | Sends secondary address after LISTN | *** ***
FF96 | TKSA | * | Sends secondary address after TALK | *** ***
FF99 | MEMTOP | * * | Read or set the top of system RAM. | ***
FF9C | MEMBOT | * * | Read or set the bottom of system RAM. | ***
FF9F | KEY | | Scans Keyboard | ***
FFA2 | SETMO | | -- Unimplemented Subroutine in All -- | [N/A]
FFA5 | ACPTR | * | Grabs byte from current talker | *** ***
FFA8 | CIOUT | * | Output byte to current listener | *** ***
FFAB | UNTLK | * | Commands device to stop talking | *** ***
FFAE | UNLSN | * | Commands device to stop listening | *** ***
FFB1 | LISTN | * | Commands device to begin listening | *** ***
FFB4 | TALK | * | Commands device to begin talking | *** ***
FFB7 | READSS | * | Returns I/O status byte | ***
FFBA | SETLFS | | Sets logical #, device #, secondary # | ***
FFBD | SETNAM | | Sets pointer to filename. | ***
FFC0 | OPEN | * * * * | Opens up a logical file. | ***
FFC3 | CLOSE | * * * * | Closes a logical file. | ***
FFC6 | CHKIN | * * * * | Set input channel | ***
FFC9 | CHKOUT | * * * * | Set output channel | ***
FFCC | CLRCH | * * | Restore default channels | ***
FFCF | BASIN | * * | Input from channel | ***
FFD2 | BSOUT | * * | Output to channel (aka CHROUT) |*** ***
FFD5 | LOAD | * * * * | Load data from file | ***
FFD8 | SAVE | * * * * | Save data to file | ***
FFDB | SETTIM | | Sets internal (TI$) clock | ***
FFDE | RDTIM | * * * | Reads internal (TI$) clock | ***
FFE1 | STOP | * * | Scans and check for STOP key | ***
FFE4 | GETIN | * * * * | Reads buffered data from file | ***
FFE7 | CLALL | * * | Close all open files and channels | ***
FFEA | UDTIM | * * | Updates internal (TI$) clock | ***
FFED | SCRORG | * * * | Returns current window/screen size |***
FFF0 | PLOT | * * * | Read or set cursor position |***
FFF3 | IOBASE | * * | Read base of I/O block | ***
--------+---------+---------+---------------------------------------+-----------
+--------------------------+
| The Routines Themselves. |
+--------------------------+
A. Error handling
For the routines in the KERNAL that return status codes (indicated by the FL
status in the chart) the carry is set if there is an error. Otherwise, the
carry returned is clear. If the carry is set, the error code is returned in the
accumalator:
+-----------------------------------+
.A |Meaning | NOTE: Some of the I/O routines |
----+------------------------------ | indicate the error code via |
0 | Stop Key pressed | the READST routine when |
1 | Too Many Open Files | setting the carry. |
2 | File Already Open +------------------------------------
3 | File Not Open
4 | File Not Found
5 | Device Not Present
6 | File Was Not Opened As Input
7 | File Was Not Opened As Output
8 | File Name Not Present
9 | Illegal Device Number
41 | File Read Error
B. Device Numbers:
The following table lists the "standard" device numbers used by the C= Kernal.
+---------+----------------------------+
|Device # | Device Name |
+---------+----------------------------+
| 0 | Keyboard (standard input) |
| 1 | Cassette |
| 2 | RS-232 |
| 3 | Screen (standard output) |
| 4 - 30| Serial Bus Devices |
| 4-7 | Printers (typically)|
| 8-30| Disk Drives (typically)|
+---------+----------------------------+
C. Routine Descriptions.
Due to space limitations a fully-detailed, descriptive summary of the KERNAL
routines is not feasible. However, listed below is a description of what each
routine does, expected parameters and any notes on C=128/C=64 differences as
well as notes to clarify any possibly confusing details.
---------------------------------------------------------------------------
Routine : SPINSPOUT ** 128 ONLY **
Kernal Address: $FF47
Description : Setup CIA for BURT protocol.
Registers In : .C = 0 -> SPINP (input)
.C = 1 -> SPOUT (output)
Registers Out : .A destroyed
Memory Changed: CIA, MMU.
Routine : CLOSEALL ** 128 ONLY **
Kernal Address: $FF4A
Description : Close all files on a device.
Registers In : .A = device # (0-31)
Registers Out : .A, .X, .Y used.
Memory Changed: None.
Routine : C64MODE ** 128 ONLY **
Kernal Address: $FF4D
Description : Switches to C64 Mode
Registers In : None.
Registers Out : None.
Memory Changed: -ALL- This routine initializes and calls the C64 cold start
routine. There is no way to switch out of C64 mode once this
routine is entered.
Routine : DMACALL ** 128 ONLY **
Kernal Address: $FF50
Description : Perform DMA command (for REU)
Registers In : .X = Bank, .Y = DMA controller command
NOTE: REU registers must have been previously setup.
Registers Out : .A, .X used
Memory Changed: Dependenant upon REU registers, REU command.
Routine : BOOTCALL ** 128 ONLY **
Kernal Address: $FF53
Description : Attempts to load and execute boot sector from a drive.
Registers In : .A = drive # in ascii (usually '0' / $30)
.X = device #
Registers Out : .A, .X, .Y used. .C = 1 if I/O error.
Memory Changed: As per boot sector.
Routine : PHOENIX ** 128 ONLY **
Kernal Address: $FF56
Description : Initalizes external / internatal cartridges,check for disk boot
Registers In : None.
Registers Out : .A, .X, .Y used.
Memory Changed: Calls any auto-start catridges that are installed on the system
Routine : LKUPLA ** 128 ONLY **
Kernal Address: $FF59
Description : Search file tables for a given logical device #.
Registers In : .A = Logical Device #.
Registers Out : .C = 0 if found -> .A = Logical Device #,
.X = Logical File #,
.Y = Logical Secondary #.
.C =1 if not found.
Memory Changed: None.
Routine : LKUPSA ** 128 ONLY **
Kernal Address: $FF5C
Description : Search file tables for a given secondary address.
Registers In : .Y = Secondary address to search for.
Registers Out : As LKUPLA (see LKUPLA).
Memory Changed: None.
Routine : SWAPPER ** 128 ONLY **
Kernal Address: $FF5F
Description : Switches between 40 / 80 column screen.
Registers In : None.
Registers Out : .A, .X, .Y destroyed.
Memory Changed: Screen Editor Locations.
Routine : DLCHAR ** 128 ONLY **
Kernal Address: $FF62
Description : Initializes 80 column character set.
Registers In : None.
Registers Out : .A, .X, .Y destroyed.
Memory Changed: None.
Routine : PFKEY ** 128 ONLY **
Kernal Address: $FF65
Description : Installs a function key definition
Registers In : .A = pointer to Z-P address (3 bytes : address lo/hi/bank.)
.Y = length, .X = key # (9 = Shift RUN/STOP, 10 = HELP).
Registers Out : .C = 1 if No room, .C = 0 if successful.
.A, .X, .Y destroyed.
Memory Changed: Function Key Table modified.
Routine : SETBNK ** 128 ONLY **
Kernal Address: $FF68
Description : Sets bank for any future I/O operations
Registers In : .A = Memory Bank, .X = Bank where filename is.
Registers Out : None.
Memory Changed: None.
Routine : GETCFG ** 128 ONLY **
Kernal Address: $FF6B
Description : Get MMU configuration for a given bank.
Registers In : None.
Registers Out : None.
Memory Changed:
Routine : JSRFAR ** 128 ONLY **
Kernal Address: $FF6E
Description : Jumps to a subroutine in another bank.
Registers In : None. (See JMPFAR for mem locations IN)
Registers Out : None. (See JMPFAR for mem locations OUT)
Routine : JMPFAR ** 128 ONLY **
Kernal Address: $FF71
Description : Starts executing code in another bank.
Registers In : None.
Memory In : $02 - Bank (0-15)
$03 - PC high
$04 - PC lo
$05 - .S (Processor status)
$06 - .A
$07 - .X
$08 - .Y
Registers Out : None.
Memory Out : As memory in.
Routine : INDFET ** 128 ONLY **
Kernal Address: $FF74
Description : Execute a LDA(fetvec),Y from a bank.
Registers In : .A - pointer to Z-Page location holding address
.X - Bank (0-15), .Y - Index.
Registers Out : .A = data, .X - destroyed.
Memory Changed: None.
Routine : INDSTA ** 128 ONLY **
Kernal Address: $FF77
Description : Execute a STA(stavec),Y in a bank.
Registers In : .A - pointer to Z-Page location holding address
.X - Bank (0-15), .Y - Index.
Registers Out : .X - Destroyed.
Memory Changed: As per registers.
Routine : INDCMP ** 128 ONLY **
Kernal Address: $FF7A
Description : Executes a CMP(cmpvec),Y in a bank.
Registers In : .A = data, .X = Bank (0-15), .Y - Z-Page ptr.
Registers Out : .X destroyed, Flags set accordingly.
Memory Changed: None.
Routine : PRIMM ** 128 ONLY **
Kernal Address: $FF7D
Description : Prints null terminated string following JSR to current channel
Registers In : None.
Registers Out : None.
Memory Changed: Dependent upon current device.
Example :
[ . . . ]
JSR $FF7D ; JSR to primm, / print following string.
.ASC "Hi World!" ; String to print.
.BYT $00 ; IMPORTANT: Null Terminated.
[ . . . ]
---------------------------------------------------------------------------
Routine : CINT
Kernal Address: $FF81
Description : Setup VIC, screen values, (128: 8563)...
Registers In : None.
Registers Out : None.
Memory Changed: Screen Editor Locations.
Routine : IOINIT
Kernal Address: $FF84
Description : Initializes pertinant display and i/o devices
Registers In : C64: None. | C128: $0A04/bit 7
| 0 - Full Setup.
| 1 - Partial Setup. (no 8563 char)
Registers Out : .A, .X, .Y destroyed.
Memory Changed: CIA's, VIC, 8502 port, (C128: also optionally 8563).
Note : This routine automatically distinguishes a PAL system from a
NTSC system and sets PALCNT accordingly for use in the
time routines.
Routine : RAMTAS
Kernal Address: $FF87
Description : Clears Z-Page, Sets RS-232 buffers, top/bot Ram.
Registers In : None.
Registers Out : .A, .X, .Y destroyed.
Memory Changed: Z-Page, Rs-232 buffers, top/bot Ram ptrs
Routine : VECTOR
Kernal Address: $FF8D
Description : Copies / Stores KERNAL indirect RAM vectors.
Registers In : .C = 0 (Set KERNAL Vectors) | .C = 1 (Duplicate KERNAL vectors)
.XY = address of vectors | .XY = address of user vectors
Registers Out : .A, .Y destroyed | .A, .Y destroyed.
Memory Changed: KERNAL Vectors changed | Vectors written to .XY
Note : This routine is rarely used, usually the vectors are directly
changed themselves. The vectors, in order, are :
C128: IRQ,BRK,NMI,OPEN,CLOSE,CHKIN,CHKOUT,CLRCH,BASIN,BSOUT
STOP,GETIN,CLALL,EXMON (monitor),LOAD,SAVE
C64 : IRQ,BRK,NMI,OPEN,CLOSE,CHKIN,CHKOUT,CLRCH,BASIN,BSOUT
STOP,GETIN,CLALL,USRCMD (not used),LOAD,SAVE
Routine : SETMSG
Kernal Address: $FF90
Description : Set control of KERNAL control and error messages.
Registers In : .A bit 7 = KERNAL Control Messages (1 = on)
bit 6 = KERNAL Error Messages (1 = on)
Registers Out : None.
Note : KERNAL Control messages are those defined as Loading, Found etc
... KERNAL Error messages are I/O ERROR # messages which are
listed as follows:
Routine : SECND
Kernal Address: $FF93
Description : Sends secondary address to device after a LISTN
Registers In : .A = secondary address
Registers Out : .A used.
Memory Changed: None.
Note : Low level serial I/O - recommended use OPEN,CLOSE,CHROUT etc..
Routine : TKSA
Kernal Address: $FF96
Description : Sends secondary address to device after TALK
Registers In : .A = secondary address.
Registers Out : .A used.
Memory Changed: None.
Note : Low level serial I/O - recommended use OPEN,CLOSE,CHROUT etc..
Routine : MEMTOP
Kernal Address: $FF99
Description : Read or Set top of System Ram
Registers In : .C = 1 (Read MemTop) | .C = 0 (Set MemTop)
| .XY = top of memory
Registers Out : .XY = top of memory | None.
Memory Changed: None. | Top of memory changed.
Note : On the C=128, this routine refers to the top of BANK 0 RAM, not
BANK 1 RAM.
Routine : MEMBOT
Kernal Address: $FF9C
Description : Read or Set bottom of System Ram
Registers In : .C = 1 (Read MemBot) | .C = 0 (Set MemBot)
| .XY = bottom of memory.
Registers Out : .XY = bottom of memory | None.
Memory Changed: None. | Bottom of Memory changed.
Note : On the C=128, this routine refers to the bottom of BANK 0 RAM,
not, BANK 1 RAM.
Routine : KEY
Kernal Address: $FF9F
Description : Scans Keyboard
Registers In : None.
Registers Out : None.
Memory Changed: Relevant System Keyboard Values
Routine : SETMO
Kernal Address: $FFA2
Description : This is a routine who's code never made it into any versions
of the KERNAL on the C64, Vic-20 and C128. Thus it is of no
pratical use.
Routine : ACPTR
Kernal Address: $FFA5
Description : Get byte from current talker.
Registers In : None.
Registers Out : .A = data byte.
Memory Changed: None.
Note : Low level serial I/O - recommended use OPEN,CLOSE,CHROUT etc..
Routine : CIOUT
Kernal Address: $FFA8
Description : Output byte to current listener.
Registers In : .A = byte.
Registers Out : .A used.
Memory Changed: None.
Note : Low level serial I/O - recommended use OPEN,CLOSE,CHROUT etc..
Routine : UNTLK
Kernal Address: $FFAB
Description : Commands current TALK device to stop TALKING.
Registers In : None.
Registers Out : .A used.
Memory Changed: None.
Note : Low level serial I/O - recommended use OPEN,CLOSE,CHROUT etc..
Routine : UNLSN
Kernal Address: $FFAE
Description : Commands current listening device to stop listening.
Registers In : None.
Registers Out : .A used.
Memory Changed: None.
Note : Low level serial I/O - recommended use OPEN,CLOSE,CHROUT etc..
Routine : LISTN
Kernal Address: $FFB1
Description : Commands device to begin listening.
Registers In : .A = device #.
Registers Out : .A used.
Note : Low level serial I/O - recommended use OPEN,CLOSE,CHROUT etc..
Routine : TALK
Kernal Address: $FFB4
Description : Commands device to begin talking.
Registers In : .A = device #.
Registers Out : .A used.
Memory Changed: None.
Note : Low level serial I/O - recommended use OPEN,CLOSE,CHROUT etc..
Routine : READSS
Kernal Address: $FFB7
Description : Return I/O status byte.
Registers In : None.
Registers Out : .A = status byte. (see section on ERROR messages).
Memory Changed: None.
Routine : SETLFS
Kernal Address: $FFBA
Description : Set logical file #, device #, secondary # for I/O.
Registers In : .A = logical file #, .X = device #, .Y = secondary #
Registers Out : None.
Memory Changed: None.
Routine : SETNAM
Kernal Address: $FFBD
Description : Sets pointer to filename in preperation for OPEN.
Registers In : .A = string length, .XY = string address.
Registers Out : None.
Memory Changed: None.
Note : To specify _no_ filename specify a length of 0.
Routine : OPEN
Kernal Address: $FFC0
Description : Open up file that has been setup by SETNAM,SETLFS
Registers In : None.
Registers Out : .A = error code, .X,.Y destroyed.
.C = 1 if error.
Memory Changed: None.
Routine : CLOSE
Kernal Address: $FFC3
Description : Close a logical file.
Registers In : .A = logical file #.
Registers Out : .A = error code, .X,.Y destroyed.
.C = 1 if error
Memory Changed: None.
Routine : CHKIN
Kernal Address: $FFC6
Description : Sets input channel.
Registers In : .X = logical file #.
Registers Out : .A = error code, .X,.Y destroyed.
.C = 1 if error
Memory Changed: None.
Routine : CHKOUT
Kernal Address: $FFC9
Description : Sets output channel.
Registers In : .X = logical file #.
Registers Out : .A = error code, .X,.Y destroyed.
.C = 1 if error
Memory Changed: None.
Routine : CLRCH
Kernal Address: $FFCC
Description : Restore default input and output channels.
Registers In : None.
Registers Out : .A, .X used.
Memory Changed: None.
Routine : BASIN
Kernal Address: $FFCF
Description : Read character from current input channel.
Cassette - Returned one character a time from cassette buffer.
Rs-232 - Return one character at a time, waiting until
character is ready.
Serial - Returned one character at time, waiting if nessc.
Screen - Read from current cursor position.
Keyboard - Read characters as a string, then return them
individually upon each call until all characters
have been passed ($0d is the EOL).
Registers In : None.
Registers Out : .A = character or error code, .C = 1 if error.
Memory Changed: None.
Routine : BSOUT aka CHROUT
Kernal Address: $FFD2
Description : Output byte to current channel
Registers In : .A = Byte
Registers Out : .C = 1 if ERROR (examine READST)
Memory Changed: Dependent upon current device.
Routine : LOAD
Kernal Address: $FFD5
Description : Loads file into memory (setup via SETLFS,SETNAM)..
Registers In : .A = 0 - Load, Non-0 = Verify
.XY = load address (if secondary address = 0)
Registers Out : .A = error code .C = 1 if error.
.XY = ending address
Memory Changed: As per registers / data file.
Routine : SAVE
Kernal Address: $FFD8
Description : Save section of memory to a file.
Registers In : .A = Z-page ptr to start adress
.XY = end address
Registers Out : .A = error code, .C = 1 if error.
.XY = used.
Memory Changed: None.
Routine : SETTIM
Kernal Address: $FFDB
Description : Set internal clock (TI$).
Registers In : .AXY - Clock value in jiffies (1/60 secs).
Registers Out : None.
Memory Changed: Relevant system time locations set.
Routine : RDTIM
Kernal Address: $FFDE
Description : Reads internal clock (TI$)
Registers In : None.
Registers Out : .AXY - Clock value in jiffies (1/60 secs).
Memory Changed: None.
Routine : STOP
Kernal Address: FFE1
Description : Scans STOP key.
Registers In : None.
Registers Out : .A = last keyboard row, .X = destroyed (if stop key)
Memory Changed: None.
Note : The last keyboard row is as follows:
.A -> | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
KEY: |STOP |Q |C= |SPACE|2 |CTRL |<- |1
Routine : GETIN
Kernal Address: $FFE4
Description : Read buffered data from file.
Keyboard - Read from keyboard buffer, else return null ($00).
Rs-232 - Read from Rs-232 buffer, else null is returned.
Serial - See BASIN
Cassette - See BASIN
Screen - See BASIN
Registers In : None.
Registers Out : .A = character, .C = 1 if error.
.XY = used.
Memory Changed: None.
Routine : CLALL
Kernal Address: $FFE7
Description : Close all open files and channels.
Registers In : None.
Registers Out : .AX used.
Memory Changed: None.
Note : This routine does not _actually_ close the files, rather it
removes their prescense from the file tables held in memory.
It's recommended to use close to close files instead of using
this routine.
Routine : UDTIME
Kernal Address: $FFEA
Description : Update internal (TI$) clock by 1 jiffie (1/60 sec).
Registers In : None.
Registers Out : .A,.X destroyed.
Memory Changed: Relevant system time locations changed.
Routine : SCRORG
Kernal Address: $FFED
Description : Returns current window/screen size
Registers In : None.
Registers Out : .X - Window Row Max
.Y - Window Col Max
.A - Screen Col Max (128 only, 64 unchanged)
Memory Changed: None
Routine : PLOT
Kernal Address: $FFF0
Description : Read or set cursor position.
Registers In : .C = 1 (Read) | .C = 0 (Set)
None. | .X = Col
| .Y = Row
Registers Out : .C = 1 (Read) | .C = 0 (Set)
.X = Current Col | None.
.Y = Current Row |
Memory Changed: None | Screen Editor Locations.
Routine : IOBASE
Kernal Address: $FFF3
Description : Returns base of I/O Block
Registers In : None.
Registers Out : .XY = address of I/O block ($D000)
Memory Changed: Screen Editor Locations.
============================================================================
64K VDC RAM and an alternate GEOS128 Background Screen
by Robert A. Knop Jr. (rknop@tybalt.caltech.edu, R.KNOP1 on GEnie)
I. Introduction
GEOS, both the 64 and 128 varieties, uses bitmapped screens for its output.
In 40 columns, this means 8K of system memory is set aside for the main
screen. Then, in addition, GEOS also uses display buffering; in other words,
GEOS allocates a second 8K as a "background" (BG) screen that is used to keep
an intact copy of the foreground (FG) screen. This can be very useful for a
number of reasons; one, it can be used as an undo buffer, as it is in
geoPaint. When you have a delicate drawing, and then accidentally run the
eraser across it, the effects of the eraser are only written to the FG screen.
A click of the UNDO button brings the BG screen, with the pre-eraser version
of your painting, back to the fore. Another use is for buffering the contents
of the screen when something like a dialog box or a menu is written over it.
When a dialog box is erased, and you see whatever had been underneatg it
magically reappear, the graphics underneath are being pulled from the BG
screen.
Applications have the option not to use the BG screen. Change a couple of
vectors and flags, and you can use the 8K BG screen for application RAM.
(This is very convenient, since the BG screen is directly above the normal 22K
of application RAM in the GEOS memory map.) Of course, the application then
has to provide some way of redrawing blocks of the screen hidden by menus and
dialog boxes. geoWrite is an example of this; when you bring up, and exit
from, a dialog box in geoWrite, there is briefly a blank rectangle on the
screen before the text is redrawn on the screen.
Under GEOS128 in 80 columns, the bitmap screen is now twice as large: 640x200
instead of 320x200. The FG screen, here 16K, occupies VDC memory. The memory
used for both the 40 column FG and 40 column BG screen is used for the 80
column BG screen.
GEOS128 was written for, and runs on, 128's with only the usual 16K of VDC
RAM. And, it uses basically all 16K of this RAM. However, if you have 64K of
VDC RAM (as is the case with 128D's, and with flat 128's that have been
upgraded), you've got an additional 48K of VDC RAM that the GEOS system
doesn't touch. So, why not use some of this RAM as a 80 column BG screen?
Then, if you are writing an 80-column only application, you get an extra 16K,
the 40-column BG screen at $6000 and the 40-column FG screen at $a000, in main
memory which your application can use however it sees fit.
II. Support Routines
Only a small number of routines actually need to be written to implement this
scheme; moreover, these routines are realatively straightforward. After all,
we are simply copying memory from one part of VDC RAM to another. The VDC's
block copy feature of the VDC is very helpful in this endeavor. (See Craig
Taylor's article from last issue, or most any 128 programming guide.) The
file vdc-bg.sfx, associated with this issue of the Hacking Mag, is a
self-extracting archive with a number of geoProgrammer source files (in
geoWrite 2.1 format) and a small dippy demonstration program. The file VDC-BG
contains the following routines:
InitVDC -- make sure your VDC knows it has 64K RAM
VDCImpLine -- Imprint horizontal line from FG screen to BG screen
VDCRecLine -- Recover horizontal line from BG screen to FG screen
VDCImpRect -- Imprint rectangle from FG screen to BG screen
VDCRecRect -- Recover rectangle from BG screen to FG screen
Each Imprint routine actually uses most of the same code as the corresponding
Recover routine; all that differs is the offset to the "source" and
"destination" screens in VDC RAM. (The offset for the FG screen is $0000, and
for the BG screen is $4000.) The routines take the same arguments as the
non-VDC Imprint and Recover routines as documented in the Hitchhiker's Guide.
(You will note, however, that for whatever reason the standard GEOS
ImprintLine and RecoverLine routines were only implemented for Apple GEOS.)
Briefly, these are:
Routine: InitVDC
Pass: Nothing
Return: Nothing
Destroys: a,x
Note: This routine should be called at the very beginning of your
program before you do any writing to the FG screen or the VDC.
----------------------------------------------------------
--------------------
Routine: VDCImpLine
VDCRecLine
Pass: r3 -- left edge of line to imprint/recover (word)
r4 -- right edge of line to imprint/recover (word)
r11L -- y coordinate of line to imprint/recover (byte)
Return: r3, r4 -- processed through NormalizeX
Destroys: a,x,y,r5-r8,r11
-------------------------------------------------------------------------------
Routine: VDCImpRect
VDCRecRect
Pass: r3 -- x-coordinate of upper-left corner (word)
r2L -- y-coordinate of upper-left corner (byte)
r4 -- x-coordinate of lower-right corner (word)
r2H -- y-coordinate of lower-right corner (byte)
Return: r3,r4 -- processed through NormalizeX
Destroys: a,x,y,r5-r8,r10L,r11
------------------------------------------------------------------------------
To discuss the imprint and recover line routines, consider the ASCII diagram
of a portion of a line on the VDC screen. A x indicates a pixel that is in
the line to be copied. The I's indicate byte boundaries; the pixel below each
I is the msb of the corresponding byte in the VDC bitmap. (Bytes increase
horizontally across the screen; there is no card structure found in the 80
column bitmap screen.)
I I I I
....xxxxxxxxxxxxxxxxxxxxxxxxx...
^ \______________/ ^
left I right
residual full bytes residual
The line moving routine needs to figure the location in VDC RAM of the
leftmost full byte, the number of full bytes, and the location of the two
residual bytes; additionally, it builds a bit mask for the residual bytes,
with bits set corresponding to pixels to be copied. This mask is used to
create the proper combination of data from the source and destination screens
in the two residual bytes.
Once it knows all this, all the line routines do is (1) submit a VDC block
copy to copy the full bytes, (2) read the left residual byte from the source,
mask out the appropriate pixels, and OR it with the appropriate pixels from
the destination, and write that one byte (3) repeat (2) for the right residual
byte.
The rectangle routines simply call the line copy routines repeatedly,
(r2H)-(r2L)+1 times. (Note that while this is the most efficient way to do it
from a coding time point of view <grin>, really the rectangle routines only
need calculate the residual bit masks and the locations once. Thereafter,
locations can be updated by adding 80 (the length of a VDC line) for each new
line. The changes to the code to implement this are not difficult, and it
isn't clear why I didn't make them....)
III. Use of the Routines
In a word, you use these routines whenever you would have used the normal GEOS
imprint/recover routines. There are a few other consierations, though.
First of all, you need to set the flag dispBufferOn to ST_WR_FORE. The GEOS
system graphic routines think that the BG screen is in main memory, and thus
will not correctly use your new VDC BG screen. This means, unfortunately,
that you can't just blithely go drawing graphics, assuming that they'll be
buffered for recall when needed. However, it is not too much trouble to make
a call to VDCImpRect either right after you've made some graphic change, or
right before something potentially hazardous will happen (e.g. a call to
DoDlgBox). For instance, you might have all of your main menus be Dynamic
Submenus which call VDCImpRect before opening the submenu.
Second, you should load recoverVector with VDCRecRect. Since VDCRecRect takes
the same parameters as RecoverRectangle, it can substitute directly for it.
Once you set this vector, all menus and dialog boxes erased from the screen
automatically restore the destroyed region from your VDC BG screen.
Both of these are demonstrated in the test program included in vdc-bg.sfx.
IV. Another 32K
The alert reader will have noticed that the VDC BG screen only takes as much
memory as the VDC FG screen, i.e. 16K. Thus, even with this scheme, there is
still another 32K of free memory in VDC RAM. Quadruple buffering, anyone?
A more tantalizing prospect would be to implement a 640x400 interlaced screen
for GEOS128. This presents a number of problems, however. First, there is
that terrible flicker. But, this can be made reasonable through the use of
polarizing filters (in layman's terms, "sunglasses") and appropriate color
choices. More seriously, the GEOS kernal graphic routines all take byte
argum`>:s for Y coordinates. So, all 400 vertical pixels cannot be addressed
with those routines. Thus, sombody implementing a GEOS interlaced screen is
faced with re-writing all of the graphics routines. (Something to do with the
8K you've freed up at $a000, I suppose.) Since each 640x400 graphic screen
would require 32K of memory for the bitmap, you could still have a VDC
Background screen.
[ Note: The code discussed within this article is available via anonymous
FTP at tybalt.caltech.edu under the directory pub/rknop/hacking.mag as
vdc-bg.sfx. This will dissolve into the GEOWRITE source files.]
============================================================================
GeoPaint File Format
--------------------
by Bruce Vrieling (bvrieling@undergrad.math.waterloo.edu)
GeoPaint is an excellent graphics program written for the GEOS environment. Its
disk access is relatively quick, compared it to what a comparable program would
do on a non-GEOS equipped C64. Part of this accomplishment can be attributed to
the diskTurbo that is an integral part of GEOS. However, the special GeoPaint
file-saving scheme deserves some of the credit.
VLIR
----
GeoPaint files are always stored in Variable Length Indexed Recording files.
VLIR files offer advantages not available without GEOS. Generally speaking, VLIR
is the ultimate in RELATIVE files.
The format of a VLIR file is not that difficult to figure out. While in a
regular C64 file, the two bytes directly following the FILETYPE byte in the
directory would point to the data file following, VLIR files use these two bytes
to point to a VLIR HEADER BLOCK (don't confuse the VLIR HEADER block with the
INFO block). The first two bytes of this block are $00/FF, as the header block
is a MAXIMUM of one block long. (This is why when you VALIDATE a GEOS disk from
C64 mode, GeoPaint pictures are lost. Only the header block is recognised as
being part of the file. The rest of the picture gets deallocated in the BAM).
The remaining 254 bytes in the block are divided into 127 2-byte pointers to
tracks/sectors on the disk. These pointers point to the individual records of
the VLIR file, which may be ANY number of blocks long. The VLIR track/sector
pointers in the VLIR header block only point to the FIRST block of the chain.
From then on, the sectors chain themselves together using the normal format ie.
the first two bytes of each block point to the following block.
A sample GeoPaint VLIR header might look like this:
0000:00 FF 03 11 03 05 03 01 ........
0008:04 03 00 FF 00 FF 00 FF ........
0010:04 07 00 00 00 00 00 00 ........
etc....
The first two bytes, $00/FF, tell the drive that this is the last (and only)
block in this VLIR HEADER SECTION (will never be more than 1 block, as was
mentioned earlier). The next pair of bytes, $03/11, points to the first VLIR
record. The next two, $03/05, point to the second record.
You will notice that 5th record contains the values $00/FF. This means that for
this record, there is no picture data. We will get into exactly what the data
held in the records mean in a minute. The $00/FF entries indicate an empty
record. Finally, the 9th entry, $00/00 indicates the end of the GeoPaint file.
There is no more data beyond this point.
One note should be made. GeoPaint is not always consistent in its handling of
the data in a header block. Sometimes, it will show quite a few $00/FF
combinations before finally terminating with a $00/00. When reading the file,
I always read the entire header, as I don't trust the end of file method
mentioned above. Just remember that any track/sector link that does not contain
$00/FF or $00/00 is a valid record, with picture data.
Layout on Screen
----------------
GEOS orients the data in a GeoPaint file slightly differently than in a
PhotoScrap or an Icon. A photoscrap stores the bytes corrosponding to a screen
which looks like this:
001 002 003 004 005 ....0012
013 014 015 016 017 ....0024
Consecutive bytes are placed BESIDE each other. However, if you are at all
familiar with the layout of a C64 hi-res screen, you will know this is very
different from the layout that the VIC chip sees data. GeoPaint uses a format
identical to the VIC chip layout on screen.
GeoPaint pictures are stored in the following format:
001 009 017 025 033 ..... 313
002 010 018 026 034 ..... 314
003 011 019 027 035 ..... 315
004 012 020 028 036 ..... 316
005 013 021 029 037 ..... 317
006 014 022 030 038 ..... 318
007 015 023 031 039 ..... 319
008 016 024 032 040 ..... 320
321 329 .....
322 330 .....
323 331 .....
324 332 .....
325 333 .....
326 334 .....
327 335 .....
328 336 .....
As you can see, this is very different from the PhotoScrap format. Consecutive
bytes are NOT stored on the screen beside each other. Rather, they are stored
underneath each other into groups of 8 bytes. This makes moving the data from
the disk onto the screen that much faster, as the decompacted bytes can just be
stored on the screen after each other. Of course, this makes porting GEOS pics
to the 128's VDC that much more difficult, as the VDC conforms to the
PhotoScrap format.
Compression Method
------------------
GEOS uses an excellent compression method to store files on disk. You may have
noticed that nearly empty pictures on disk consume very little disk space. This
can be credited to GeoPaint's smart compression techniques.
Basically, the format of the compression has one COMMAND byte followed by one
or more DATA bytes. The COMMAND byte tells GEOS what to do with following DATA
bytes. There are 4 commands for compression:
1) If the COMMAND byte is less than 64, this indicates that there are 'COMMAND'
many DATA bytes following that are to be taken as individual bytes. This is
the least effective method of compression, as no compression takes place.
2) If the COMMAND byte ranges from 65 to 127, then this is a special type of
compression. First of all, the next 8 bytes in the file are read in as DATA.
This DATA is used to make an 8*8 'stamp'. Secondly, the amount of times to
'stamp' this 8*8 square is calculated (COMMAND AND 63). Then, the stamping
is done. 'Stamping' sounds more difficult that it really is. What it boils
down to, is repeating the 8 byte DATA stamp 'COMMAND AND 63'
times.
3) If the COMMAND byte is 129 or greater, then the following DATA byte is
repeated 'COMMAND AND 127' times. This is different from #1, as only 1 DATA
byte is called in, and simply repeated. #1 called in 'COMMAND' many DATA
bytes.
4) If the COMMAND byte is ZERO, we have reached the end of the VLIR record for
the GeoPaint picture.
It should be noted that the COMMAND byte will NEVER be 64 or 128. If it is,
there has been an error.
Format of Data After Decompacting
---------------------------------
After the data has been decompacted, it remains to be placed on the screen. Each
VLIR record holds 16 scanlines of data, or 2 character lines (different ways of
looking at the same thing).
The format of the data is as follows:
First, there is 640 bytes of picture data, comprising the first character
line (8 scanlines). Remember, GeoPaint pictures are 640 pixels across. 640
pixels works out to 80 bytes. A character line is 8 pixels deep, so 80*8
comes to 640 bytes.
These bytes are followed by the 640 bytes for the second chacacter line
(next 8 scanlines). This is followed by 8 garbage bytes that accidentaly
worked themselves into the original GeoPaint design. They should be set to
zero.
Finally, two sets of 80 bytes of colour data follow. The first set
comprises the colour for the first line, the second 80 bytes for the second
line. To wrap things up, the VLIR record is terminated by a zero byte.
The next VLIR record will hold the data for the NEXT 16 scanlines, and so
on.
Conclusion
----------
That about wraps up this discussion on GeoPaint format for files. We've
discussed the format of VLIR files on disk, layout of picture data on screen,
compression methods used in GeoPaint files, and the format of the data once
decompacted. I hope this information will come in handy for someone.
==============================================================================
Rasters - What They Are and How to Use Them
by Bruce Vrieling - (bvrieling@undergrad.math.waterloo.edu)
Anyone who has fiddled around with interrupts on the Commodore 64 has
undoubtedly heard at one time or another of the concept of rasters being
mentioned. Rasters are the 'ultimate' achievement of interrupt programming, or
so they say. What is a raster? And how does one go about writing a program to
use them?
Overview of what Interrupts are all about
-----------------------------------------
A raster is sort form for the concept of a 'raster interrupt'. Before
going into rasters, perhaps a brief review of interrupts is in order.
Interrupts are events generated by the CIA timer in the C64 to perform certain
tasks. 60 times a second, the CIA chip signals an interrupt is due to be
processed (ie. the interrupt timer timed out). This causes the 6510 CPU to stop
executing the current program, save the registers on the stack, and begin to
execute the interrupt code. Some of the things which get done during an
interrupt include the keyboard scan, and updating TI (the software clock). When
the interrupt code is finished, an RTI instruction is executed, which brings
the interrupt's execution to a halt. The registers are retrieved from the stack,
and the current program in memory continues to execute once again. It will
continue to do so until the next interrupt occurs, about 1/60 of a second later.
The above is what happens in a normal C64 (the C128 follows the same idea, but
more events occur during a C128 interrupt). [Ed. Note: In addition, the C=128
generates its interrupts via a screen raster instead of the CIA chip.]
However, you can change the normal course of events, and cause some code of your
design to be added to the normal list of events which occur every interrupt.
Some of the simple favourites include flashing the border 60 times per second.
(Note that we have not begun the topic of rasters yet; this has nothing to do
with rasters. That discussion begins at the next heading.)
How do you change the interrupt's normal course of action? It's rather simple.
The C64 contains an interrupt VECTOR at locations 788/9 which is 'jumped
through' before the Kernal Rom gets a chance to execute its code. If you change
this vector to point to YOUR code, and make the end of your code point to the
normal Kernal location (where the interrupt normally would have jumped to,
$EA31), and you are careful not to step on anything, your code will be executed
60 times per second.
An example is in order:
; flasher
;
; this program causes the border to flash 60 times per second
;
setup = *
sei ; disable interrupts
lda #<intcode ; get low byte of target routine
sta 788 ; put into interrupt vector
lda #>intcode ; do the same with the high byte
sta 789
cli ; re-enable interrupts
rts ; return to caller
intcode = *
inc $d020 ; change border colour
jmp $ea31 ; exit back to rom
The above is an example of a very simple interrupt routine. If you were to
assemble it with an assembler, and SYS to the SETUP routine, you would see your
border flash 60 times per second.
You will notice the SEI and CLI machine language instructions used above. They
are very important. We don't want an interrupt occurring in between the STA 788
and the STA 789 instructions.
Think what would happen if one did: 788 would have been modified, but 789 would
still be pointing to the high byte of the Kernal address. Result: the interrupt
would have jumped to heaven knows where. You can be virtually guaranteed that
it would NOT be pointing to a valid piece of interrupt code. Your machine would
crash. The SEI instruction turns interrupts OFF, so that there is no danger of
an interrupt occurring during execution of the following routine. The CLI turns
them back on. If you forget to turn them back on, and accidentally leave them
off, your keyboard will freeze when you return to basic, and your machine will
seem to lock up.
The above was a very simple example. There are many useful things which can also
be done on an interrupt. I have seen code which played music in the background
of a running Basic program (it played the popular .MUS files). GEOS uses
interrupts extensively to control the pointing of the mouse, and to trigger
events. Interrupts are powerful beasts, and the following concept concerning
raster interrupts specifically is a particularly useful animal for some people.
The Raster
----------
A raster is a loosely used term. It refers to an interrupt that is triggered
when the ray gun on the back of your monitor draws a certain line on the video
screen. There are many different sources which can cause an interrupt. You are
not limited to what the CIA chip can do. Rasters depend on interrupts
specifically generated by the VIDEO chip. You could make this interrupt change
the border colour of the screen below a certain screen line. When the screen
line you specified gets redrawn, the interrupt goes off. Your code then quickly
changes some memory locations to create a different video mode or effect. You
could cause the bottom half of the screen to gets it's character definitions
from another, different character set. Or, you could make the top 3/4 of your
screen exist in hi-res multi-colour graphics, and keep the bottom 1/4 of the
screen in text mode.
Some facts about the video screen: it gets redrawn exactly 60 times per second.
It contains 200 scan lines on the normal 25*40 display, numbered 50 to 250 or
thereabouts (note that there are more visible scan lines though: the top and
bottom borders, for example). The actual re-drawing of the screen is
synchronized to the electrical power coming into your house, 60 Hz. That's why
some programs behave differently when run on European machines. The power is
delivered at 50 Hz over there.
Why do we have to worry about a video interrupt? If the screen gets redrawn 60
times per second, and regular interrupts also occur at 60 times per second, why
not simply put some code into the regular interrupt to do what we want with the
screen? Because the two types of interrupts are not in sync. Neither one of them
occurs EXACTLY 60 times per second, and the differences are enough to make it
next to impossible to get coordinated activity of any kind happening on the
screen. When we use the video interrupt, we KNOW we are at a certain line on the
screen, as being on that line is what caused the interrupt to happen in the
first place.
So, let's summarize. We know that regular interrupts occur 60 times per second.
We also know that the video screen gets re-drawn 60 times per second, and that
we can cause an interrupt to be generated when a certain line gets drawn on the
screen. One slight drawback to all of this is that BOTH types of interrupts
(regular and raster driven) travel through the SAME vector (ie. about 120
interrupts per second, 60 of one, and 60 of the other). Your code will have to
check and see what the source of the interrupt was, and act accordingly. Or will
it?
The system needs an interrupt to occur 60 times per second to do housekeeping,
and uses the CIA clock to generate the interrupts. We want to interrupt every
time a certain scan line is reached on the monitor, which will also just happen
to occur at 60 times per second. We also have to make sure that they don't
interfere with each other. The regular interrupts should be sent to their Rom
destination, while our video interrupts should go to our code, and no where
else.
If both are occurring at 60 times per second, why not do the job of the system
Rom, and our video code on the SAME interrupt? We know that the CIA chip is not
good for this; it is out of sync with the video image. Why not turn OFF the CIA
interrupt, enable the raster/video interrupt, and do both jobs on one interrupt?
Then we would have an interrupt signal that occurs 60 times per second, and is
in perfect sync with the video image.
That's exactly what we're going to do.
Astute reads will notice a slight flaw in the above logic. For simplification
purposes, I didn't get into the fact that you will need TWO raster interrupts
PER SCREEN to accomplish anything useful. Why two? Because any change to the
video mode you put into effect 3/4 of the way down the screen will have to be
undone at the TOP of the next screen update. If you decide to make the top 3/4
of the screen a hi-res image, and the bottom 1/4 text, you need one interrupt
3/4 of the way down the screen to change from hi-res to text, but you need a
SECOND one at the top of the screen to change back to hi-res from text.
So, we will now have 120 interrupts going off every second to accomplish our
video desires, with 60 of them working a double shift, making sure the system
interrupt code gets executed also. Remember that we are working with a specific
example. There is no reason why you couldn't split the screen into N different
video modes, and have (N+1)*60 interrupts going off per second. As long as you
keep your code short (so your interrupts don't take too long, and have another
interrupt occur before the current one is done - messy), it will work
beautifully.
So far, this is all talk. Let's write a few short code segments to accomplish
some of the feats we've just discussed.
The first we'll do is a re-hash of the one presented above. It flashes the
border again. It does not do any mid-screen changes of video modes or anything
fancy like that, so only 1 interrupt per screen is required (ie. 60 per second,
not 120 etc.). This program simply shows the same idea, but this time using
video interrupts as the source rather than the CIA. You probably won't
notice a difference during execution.
----------------------------------------------------------------------------
; flasher - part II
;
; this program causes the border to flash 60 times per second
; the source of the interrupts is the video chip
;
setup = *
sei ; disable interrupts
lda #$7f ; turn off the cia interrupts
sta $dc0d
lda $d01a ; enable raster irq
ora #$01
sta $d01a
lda $d011 ; clear high bit of raster line
and #$7f
sta $d011
lda #100 ; line number to go off at
sta $d012 ; low byte of raster line
lda #>intcode ; get low byte of target routine
sta 788 ; put into interrupt vector
lda #<intcode ; do the same with the high byte
sta 789
cli ; re-enable interrupts
rts ; return to caller
intcode = *
inc $d020 ; change border colour
lda $d019 ; clear source of interrupts
sta $d019
lda #100 ; reset line number to go off at
sta $d012
jmp $ea31 ; exit back to rom
--------------------------------------------------------------------------
As you can tell, there's a wee bit more to this code than there was in the
original. Execute it, and you'll notice that it looks pretty much the same as
the results from the first program. But there's a difference: the interrupts
are now being generated from the video chip, not the CIA. For this program, it
didn't make much difference. However, for a more complicated program, it makes
a world of difference.
I'd better explain some of the code used above:
lda #$7f
sta $dc0d
- This piece disables any interrupts caused by the CIA chip.
lda $d01a
ora #$01
sta $d01a
- Location $d01a controls which sources may cause an interrupt
(other than the normal CIA). There are 4 different possible
sources: rasters, sprite to sprite collision, sprite to
background collision, and the light pen. Bit #0 is the raster
bit, and this piece of code activates it.
lda $d011
and #$7f
sta $d011
- This code clears bit #7 of location $d011. This location is used
for many different things. Bit #7 represents the highest bit of
the raster line (see segment below for more on the raster line
#). More than 256 raster line numbers are possible (some are off
screen, and some represent the upper and lower border areas).
This bit is the 9th bit. I set it to zero because all my code
affects rasters only on the normal 25*40 line display, well
within the 0-255 range. This decision was an arbitrary choice on
my part, to make the code simpler.
lda #100
sta $d012
- Location $d012 is the lower 8 bits of the raster line on which
the interrupt is to be generated. The number 100 was another
arbitrary choice. For changing border colours, the actual line
number was not important. Later on, in the next example, it will
become important.
lda #>intcode
...
rts
- Re-vectors the interrupt code to the new code.
inc $d020
- Changes the border colour.
lda $d019
sta $d019
- These lines clear the bit in the interrupt register which tells the
source of the interrupt (in preperation for the next).
lda #100
sta $d012
- This line resets the raster line to go off at line number 100
again (same as above). It should be reset, so the next interrupt
will know what line to occur on.
jmp $ea31
- Exit back to the Kernal Rom.
A Useful Example
----------------
The following is an example of a more sophisticated piece of raster code. It
makes the top half of the screen border white, and the bottom half black.
---------------------------------------------------------------------------
setup = *
; some equates
COLOUR1 = 0
COLOUR2 = 1
LINE1 = 20
LINE2 = 150
; code starts
setup = *
sei ; disable interrupts
lda #$7f ; turn off the cia interrupts
sta $dc0d
lda $d01a ; enable raster irq
ora #$01
sta $d01a
lda $d011 ; clear high bit of raster line
and #$7f
sta $d011
lda #LINE1 ; line number to go off at
sta $d012 ; low byte of raster line
lda #>intcode ; get low byte of target routine
sta 788 ; put into interrupt vector
lda #<intcode ; do the same with the high byte
sta 789
cli ; re-enable interrupts
rts ; return to caller
intcode = *
lda modeflag ; determine whether to do top or
; bottom of screen
beq mode1
jmp mode2
mode1 = *
lda #$01 ; invert modeflag
sta modeflag
lda #COLOUR1 ; set our colour
sta $d020
lda #LINE1 ; setup line for NEXT interrupt
sta $d012 ; (which will activate MODE2)
lda $d019
sta $d019
jmp $ea31 ; MODE1 exits to Rom
mode2 = *
lda #$00 ; invert modeflag
sta modeflag
lda #COLOUR2 ; set our colour
sta $d020
lda #LINE2 ; setup line for NEXT interrupt
sta $d012 ; (which will activate MODE1)
lda $d019
sta $d019
pla ; we exit interrupt entirely.
tay ; since happening 120 times per
pla ; second, only 60 need to go to
tax ; hardware Rom. The other 60 simply
pla ; end
rti
modeflag .byte 0
----------------------------------------------------------------------------
The above code, when executed, will result in the top half of your border being
white, and the bottom black. You may wish to fiddle with the equates (COLOUR1,
COLOUR2, LINE1, and LINE2) to get different effects.
I see some confused faces concerning why the above exit the interrupts the way
they do. Remember, since we want a split screen effect, we have to have one
interrupt occur at the TOP of the screen, to turn on the WHITE effect, and one
midway down to turn on the BLACK effect. Two interrupts times 60 means 120
interrupts will be executed per second. The Rom only needs 60 per second to
service the keyboard and its other stuff. So, we send 60 to the Rom (the
interrupts which go through MODE1) by JMPing to $EA31, and the other 60 we
trash. The PLA... RTI business is the proper way to bring an interrupt to an end
without going through the Rom. The RTI will ReTurn from Interrupt, and cause the
regular program to continue to execute.
That brings to an end this discussion on rasters. I hope the above examples
have proved to be a valuable learning tool for you. With luck, they will
motivate you to continue to experiment with rasters, and come up with some neat
effects.
If you have any questions, be sure to ask me about them.
==============================================================================
BURSTING YOUR 128: THE FASTLOAD BURST COMMAND
by Craig Bruce <f2rx@jupiter.sun.csd.unb.ca>
1. INTRODUCTION
This article discusses the well-unknown Fastload command of the 1571 and 1581
disk drive Burst Command Instruction Set. If you look in the back of your '71
(or '81 I presume) disk drive manual, you will find that the information given
about the Fastload utility is not exactly abundant.
The Fastload command was intended to load program files into memory for
execution, but it can be used just as well for reading through sequential
files that would be much too large to load into a single bank of internal
memory.
To make use of the Fastload burst command, I implement a word counting utility
that will count the number of lines, words, and characters in a text file on a
1571 or 1581 disk drive. The advantage of using the Fastload command over
regular sequential file accessing through the kernel and DOS is that the
Fastload operates about 3.5 times faster on both drives.
2. WORD COUNTING UTILITY
To use the word counting program, LOAD and RUN it like a regular BASIC
program. It will ask you for the name of a file. Enter the name if it is on
device number 8, or put a one character prefix and a ":" if it is on another
device. A "b" means device 9, "c" device 10, etc. The following are examples
of valid names:
. filename "filename" on device 8
. b:filename "filename" on device 9
. a:filename "filename" on device 8
The file must be on either a 1571 or 1581 disk drive; the program will not
work with non-burst devices. The program will work with either PRG or SEQ
files, since the Fastload command can be told not to worry about the file
type.
I use the same definition of a word as the Unix "wc" command uses: a sequence
of characters delimited by whitespace, where whitespace is defined to be
SPACE, TAB, and NEWLINE (Carriage Return) characters. To get the line count,
I simply count the number of NEWLINEs. If the last line of the file does not
end with a NEWLINE character, then the count will be one line short. This is
the same as the Unix wc command too. A proper text file should have its last
line end with a NEWLINE character.
On my JiffyDOS-ified 1571 and 1581, I am able to achieve a word counting speed
of 5,400 chars/sec and 6,670 chars/sec, respectively. I am not sure how much
of a difference JiffyDOS makes, but I am not willing to rip out the ROMs to
check. I tested using a 318K file.
3. BURST READ LIBRARY
This section presents the burst reading library that you can incorporate into
your own programs and describes how the burst commands work. The library has
three calls:
. burstOpen ( .A=Device, .X=NameLen, burstBuf=Filename ) : <first block>
. burstRead () : burstBuf, burstStatus, burstBufCount
. burstClose ()
I define three common storage variables for using this package: "burstBuf",
"burstStatus", and "burstBufCount". "burstBuf" is a 256 byte area where the
data read in from the disk drive is stored before processing, and is located
at $0B00. "burstStatus" is a zero-page location that keeps the status
returned from the burst command system. This is needed by the user to detect
when the end of file has been encountered. "burstBufCount" gives the number
of data bytes available in "burstBuf" after an open or read operation. Its
value will be somewhere between 1 and 254. A full sector contains 254 bytes
of data and two bytes of control information.
"burstStatus" and "burstBufCount" are defined to be at locations $FE and $FF,
respectively. You are allowed to alter the values of the two variables and
the data buffer between calls, if you wish. For reasons not completely
understood, interrupts must be disabled for the entire course of burst reading
a file. I suspect this is because the IRQ service routine reads the interrupt
mask register of CIA#1, thus clearing the SerialDataReady flag that the burst
read routine waits for. Anyway, the open routine does a SEI and the close
routine does a CLI, so you don't have to do this yourself.
If an error occurs during the exection of one of these routines, it will
return with the carry flag set and with the error code in the .A register
(same as the kernel (yes, I know that Commodore likes to call it the
"kernAl")). Error codes 0 to 9 correspond to the standard kernel codes, error
code 10 means that the device is not a burst device, and error codes 16 to 31
correspond to the burst controller status codes 0-15. If no error occurs, the
routines return with the carry flag clear, of course.
Only one file may be open at a time for Fastloading, since Fastload takes over
the disk drive and the entire serial bus. Even regular files cannot be
accessed while a fastload is in progress. Thus, Fastload is not suitable for
all file processing applications, but it works very well for reading a file
into memory (like for a text editor) and for summarization operations (like
word counting). The burst library requires that the kernel and I/O space be
in context when it is called.
3.1. BURST OPEN
The way that a burst command is given is to give a magical incantation over
the command channel to the disk drive. You can either use the low-level
serial bus calls (LISTN, SECND, CIOUT, and UNLSN) or use the OPEN and CHROUT
calls. I used the low level calls for a little extra zip.
The burst command format for Fastload is given in the back of your drive
manual:
. BYTE \ bit: 7 6 5 4 3 2 1 0 | Value
. -------+--------+-----+-----+-----+-----+-----+-----+-----+-------
. 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | "U"
. 1 | 0 | 0 | 1 | 1 | 0 | 0 | 0 | 0 | "0"
. 2 | P | X | X | 1 | 1 | 1 | 1 | 1 | 159
. 3 - ?? | <filename> |
. -------+--------------------------------------------------+-------
where "X" means "don't case" and "P" means "program". If the P bit is '0'
then only program (PRG) files can be loaded, and if it is '1' then sequential
(SEQ) files can be loaded as well. The package automatically sets this flag
for you. Note that you don't have to do an Inquire Disk or Query Disk Format
in order to use this command like you have to do with the block reading and
writing commands.
If you want to try giving the incantation yourself, enter:
OPEN1,8,15,"U0"+CHR$(159)+"FILENAME"
(where "FILENAME" is the name of some file that exists on your disk) on your
128 and your disk drive will spring to life and wait for you to read the file
data. You can't read the data from BASIC, so to cancel the command:
CLOSE1
The "burstOpen" call of this package accepts the name of the file to be loaded
at the start of the "burstBuf" buffer, the length of the filename in the .X
register, and the device number to load the file from in the .A register. The
burst command header and the filename are sent to the disk drive as described
above.
The open command also reads the first sector of the file, for two reasons.
First, the status byte returned for the first sector has special meaning.
Status code $02 means "file not found". The package translates this into the
kernel error code. Second, and most important, there is a bizarre feature
(read: "bug") in the Fastload command. If the file to be read is only one
block long, then the number of bytes reported for the block length is two
bytes too short. The following table gives the number of bytes reported and
the number of actual bytes in the sector:
. Actual | 4 | 3 | 2 | 1 | 0 |
. ---------+---------+---------+---------+---------+---------+
. Reported | 2 | 1 | 0 | 255 | 255 |
This is where I ran into problems with Zed-128; the logic of my program
screwed up on a zero length. I have corrected the problem here, though. This
bug is bizarre because it only happens if the first sector is the only sector
in the file. The reported length for all subsequent sectors is correct. Note
also that 255 is reported for lengths of both 1 and 0. This is because there
is no actual zero length for Commodore files. If you OPEN1,8,2,"EMPTY" and
then immediately CLOSE1 you get a file with one carriage return character in
it.
The open routine calls the read routine to read a sector and if it was the
only sector of the file, the two additional bytes are burst-read and put into
the data buffer. Note that incrementing the reported count of 255 twice gives
the correct count of 1. Also interesting in this case is that when the
1571/81 reports the 255, it actually transfers 255 bytes of data, all of which
are bogus. It seems to me that they made the 1581 bug-compatible with the
1571 in this respect.
The open routine also executes a SEI for reasons discussed above. The
information returned by the open call is the same as what is returned for the
"burstRead" call discussed next.
3.2. BURST READ
Once the Fastload command is started, the drive starts waiting to transfer the
data to you. The transfer occurs sector by sector, with each sector preceeded
by a burst status byte. The data is transferred using the shift register of
CIA#1 and the handshaking is done using the Slow Serial Clock line of CIA#2.
To receive a byte, you toggle the Slow Serial Clock line and wait for the
Shift Register Ready signal from CIA#1 and then read the data value from the
shift data register.
One of the clock registers in the CIA in the 1571/81 is used as the baud rate
generator for the serial line. I think that it uses a delay of 4 microseconds
per bit, which gives a baud rate of 250,000 (31.25K/sec). In my
experimentation, the maximum baud rate I have ever achieved in reality is
200,000 (25K/sec). I read in my 1571 Internals book that the 250,000 baud
rate cannot actually be achieved because of electrical problems that I don't
understand. This is an important difference because the data comes flying off
the surface of the disk at around 30K/sec and if the serial bus were fast
enough, it could be transferred to the computer as it is being read. Some
things would be so much more convenient if whomever created the universe had
thought to make light go just a little bit faster.
The burst handshaking protocol slows the maximum transfer rate down to about
16K/sec. Of course, the disk drive has more things to keep on top of than
just transferring data, so the actual burst throughput is lower than that:
about 5.4K/sec with my JiffyDOS-ified 1571 and about 7K/sec with a 1581. Note
that you can probably increase your 1571's burst performance a bit by setting
it to use a sector interleave factor of 4, using the "U0>S"+CHR$(i) burst
command. By default, a 1571 writes files with an interleave of 6.
All of the sectors before the last one will contain 254 bytes of data and the
last one will contain a specified number of bytes, from 1 to 254. The status
code returned for the last sector is value $1F. In this case, an additional
byte is sent before the data bytes that tells how many data bytes there will
be. This is the value that is bugged for one-sector files as described in the
last section. For those who like pictures, here are diagrams of the data
transferred for a sector:
. REGULAR SECTOR LAST SECTOR OF FILE
. +-------------------+ +--------------------+
. 0 | Burst Status Byte | 0 | Burst Status = $1F |
. +-------------------+ +--------------------+
. 1 | | 1 | Byte Count = N |
. ... + 254 Data Bytes | +--------------------+
. 254 | | 2 | |
. +-------------------+ ... | N Data Bytes |
. N+1 | |
. +--------------------+
If a sector returns a burst status code other than 0 (ok) or $1F (end), then
an error has occurred and the disk drive aborts the transfer, closes the burst
connection, and starts the drive light blinking.
The "burstRead" call of this package reads the data of the next sector of the
opened file into the "burstBuf" and returns the "burstStatus" and
"burstBufCount" (bytes read). In the event of an error occuring, this routine
returns with the carry flag set and the translated burst error code in the .A
register (same as burstOpen). When the last sector of the file has just been
read, this routine returns with a value of $1F in the "burstStatus" variable.
3.3. BURST CLOSE
After reading the last data byte of the last sector of the file, the burst
connection and is closed automatically by the disk drive. The "burstClose"
routine is not necessary for communication with the disk drive, but is
provided for completeness and to clear the interrupt disable bit (CLI) that
the open routine set to prevent interrupts while burst reading.
3.4. PACKAGE USAGE
The following pseudo-code outlines how a user program is expected to use the
burst reading package:
. jsr put_filename_into_burstBuf
. ldx #filename_length
. lda #device_number
. jsr burstOpen
. bcs reportError
. L1: jsr process_burstBuf_data
. lda burstStatus
. cmp #$1f
. beq L2
. jsr burstRead
. bcc L1
. jsr reportError
. L2: jsr burstClose
4. IMPLEMENTATION
This section discusses the code that implements the word counting program. It
is here in a special form; each code line is preceeded by a few special
characters and the line number. The special characters are there to allow you
to easily extract the assembler code from the rest of this magazine (and all
of my ugly comments). On a Unix system, all you have to do is execute the
following command line (substitute filenames as appropriate):
grep '^\.%...\!' Hack3 | sed 's/^.%...\!..//' | sed 's/.%...\!//' >wc.asm
.%001! ;Word Count utility using the burst command set's Fastload facility
.%002! ;written 92/06/25 by Craig Bruce for C= Hacking Net Magazine
.%003!
The code is written for the Buddy assembler and here are a few setup
directives.
.%004! .mem
.%005! .bank 15
.%006! .org $1c01
.%007!
.%008! ;*** BASIC startup code
.%009!
This is what the "10 sys 7200" in BASIC looks like. It is here so this
program can be executed with BASIC RUN command.
.%010! .word $1c1c
.%011! .word 10
.%012! .byte $9e
.%013! .asc " 7200 : "
.%014! .byte $8f
.%015! .asc " 6502 power!"
.%016! .byte 0
.%017! .word 0
.%018! .word 0
.%019!
.%020! jmp main
.%021!
.%022! ;========== burst read library ==========
.%023!
.%024! burstStatus = $fe
.%025! burstBufCount = $ff
.%026! burstBuf = $b00
"serialFlag" is used to determine whether a device is Fast or not, and the
"ioStatus" (a.k.a. "ST") is to tell if a device is present or not.
.%027! serialFlag = $a1c
.%028! ioStatus = $90
"ciaIcr" is the interrupt control register of CIA#1. It is polled to wait for
data becoming available in the shift register ("ciaData"). "ciaSerialClk" is
the Slow serial bus clock line that is used for handshaking on the Fast bus.
.%029! ciaIcr = $dc0d
.%030! ciaSerialClk = $dd00
.%031! ciaData = $dc0c
.%032!
.%033! kernelListen = $ffb1
.%034! kernelSecond = $ff93
.%035! kernelCiout = $ffa8
.%036! kernelUnlsn = $ffae
.%037! kernelSpinp = $ff47
.%038!
This is the error code value this package returns if it detects that a device
is not Fast.
.%039! errNotBurstDevice = 10
.%040!
.%041! burstFilenameLen = burstBufCount
.%042!
.%043! burstOpen = * ;(.A=Device, burstBuf=Filename, .X=NameLen):<first block>
Set up for a burst open: clear the Fast flag and the device not present flag.
.%044! stx burstFilenameLen
.%045! pha
.%046! lda serialFlag
.%047! and #%10111111
.%048! sta serialFlag
.%049! lda #0
.%050! sta ioStatus
.%051! pla
Command the disk device to Listen. Then check if the device is present or not
(bit 7 of ioStatus). If not present, return the kernel error code.
.%052! jsr kernelListen
.%053! bit ioStatus
.%054! bpl +
.%055!
.%056! devNotPresent = *
.%057! jsr kernelUnlsn
.%058! lda #5
.%059! sec
.%060! rts
.%061!
Tell disk device to listen on the command channel (channel #15).
.%062! + lda #$6f
.%063! jsr kernelSecond
Send the "U0"+CHR$(159) burst command header.
.%064! lda #"u"
.%065! jsr kernelCiout
.%066! bit ioStatus
.%067! bmi devNotPresent
.%068! lda #"0"
.%069! jsr kernelCiout
.%070! lda #$9f
.%071! jsr kernelCiout
Send the filename.
.%072! ldy #0
.%073! - lda burstBuf,y
.%074! jsr kernelCiout
.%075! iny
.%076! cpy burstFilenameLen
.%077! bcc -
Finish sending the burst command and make sure the device is Fast.
.%078! jsr kernelUnlsn
.%079! lda serialFlag
.%080! and #$40
.%081! bne +
.%082! sec
.%083! lda #errNotBurstDevice
.%084! rts
.%085!
Disable interrupts.
.%086! + sei
Prepare to receive data and signal the disk drive to start sending (by
toggling the slow serial Clock line).
.%087! clc
.%088! jsr kernelSpinp
.%089! bit ciaIcr
.%090! lda ciaSerialClk
.%091! eor #$10
.%092! sta ciaSerialClk
Read the first sector of the file.
.%093! jsr burstRead
Check for errors. Burst error code 2 (file not found) is translated to its
kernel equivalent.
.%094! lda burstStatus
.%095! cmp #2
.%096! bcc +
.%097! bne shortFile
.%098! sec
.%099! lda #4
.%100! + rts
.%101!
Check if this is a one-block file.
.%102! shortFile = *
.%103! cmp #$1f
.%104! bne openError
.%105! ldy burstBufCount
.%106! ldx #2
.%107!
If so, we have to read the two bytes that the disk drive forgot to tell us
about. For each byte, we wait for for the Shift Register Ready signal, toggle
the clock, and read the shift data register. I can get away with reading the
data register after sending the acknowledge signal to the disk drive because I
am running with interrupts disabled and it could not possibly send the next
byte before I pick up the current one. We wouldn't want any NMIs happening
while doing this, though.
.%108! shortFileByte = *
.%109! lda #$08
.%110! - bit ciaIcr
.%111! beq -
.%112! lda ciaSerialClk
.%113! eor #$10
.%114! sta ciaSerialClk
.%115! lda ciaData
.%116! sta burstBuf,y
.%117! iny
.%118! dex
.%119! bne shortFileByte
Store the updated byte count and exit.
.%120! sty burstBufCount
.%121! clc
.%122! rts
.%123!
In the event of a burst error, re-enable the interrupts since the user might
not call the burstClose routine. Return the translated error code.
.%124! openError = *
.%125! cli
.%126! sec
.%127! ora #$10
.%128! rts
.%129!
Read the next sector of the file.
.%130! burstRead = * ;( ) : burstBuf, burstBufCount, burstStatus
Wait for the status byte to arrive.
.%131! lda #8
.%132! - bit ciaIcr
.%133! beq -
Toggle clock line for acknowledge.
.%134! lda ciaSerialClk
.%135! eor #$10
.%136! sta ciaSerialClk
Get status byte and check. If 2 or more and not $1F, then an error has
occurred. If 0, then prepare to read 254 data bytes.
.%137! lda ciaData
.%138! sta burstStatus
.%139! ldx #254
.%140! cmp #2
.%141! bcc actualRead
.%142! cmp #$1f
.%143! bne openError
If status byte is $1F, then get the next byte, which tells how many data bytes
are to follow.
.%144! lda #8
.%145! - bit ciaIcr
.%146! beq -
.%147! ldx ciaData
.%148! lda ciaSerialClk
.%149! eor #$10
.%150! sta ciaSerialClk
.%151!
.%152! actualRead = *
.%153! stx burstBufCount
.%154! ldy #0
.%155!
Read the data bytes and put them into the burst buffer. The clock line toggle
value is computed before receiving the data for a little extra zip. I haven't
experimented with this, but you might be able to toggle the clock line before
receiving the data (however, probably not for the first byte).
.%156! readByte = *
.%157! lda ciaSerialClk
.%158! eor #$10
.%159! tax
.%160! lda #8
.%161! - bit ciaIcr
.%162! beq -
.%163! stx ciaSerialClk
.%164! lda ciaData
.%165! sta burstBuf,y
.%166! iny
.%167! cpy burstBufCount
.%168! bne readByte
.%169! + clc
.%170! rts
.%171!
Close the burst package: simply CLI.
.%172! burstClose = *
.%173! cli
.%174! clc
.%175! rts
.%176!
.%177! ;========== main program ==========
.%178!
This is the word counting application code.
.%179! bkWC = $0e
.%180! bkSelect = $ff00
.%181! kernelChrin = $ffcf
.%182! kernelChrout = $ffd2
.%183!
The "wcInWord" is a boolean variable that tells whether the file scanner is
currently in a word or not. The Lines, Words, and Bytes are 24-bit counters.
.%184! wcInWord = 2 ;(1)
.%185! wcLines = 3 ;(3)
.%186! wcWords = 6 ;(3)
.%187! wcBytes = 9 ;(3)
.%188!
.%189! main = *
Put the kernel ROM and I/O space into context then initialize the counting
variables.
.%190! lda #bkWC
.%191! sta bkSelect
.%192! jsr wcInit
Follow the burst reading procedure outline.
.%193! jsr wcGetFilename
.%194! jsr burstOpen
.%195! bcc +
.%196! jsr reportError
.%197! rts
.%198! / jsr wcScanBuffer
.%199! lda burstStatus
.%200! cmp #$1f
.%201! beq +
.%202! jsr burstRead
.%203! bcc -
.%204! jsr reportError
.%205! + jsr burstClose
Report the numbers of lines, words, and characters and then exit.
.%206! jsr wcReport
.%207! rts
.%208!
Initialize the variables.
.%209! wcInit = *
.%210! lda #0
.%211! ldx #8
.%212! - sta wcLines,x
.%213! dex
.%214! bpl -
.%215! sta wcInWord
.%216! rts
.%217!
Get the device and filename from the user. Returns parameters suitable for
passing to burstOpen.
.%218! wcGetFilename = * ;() : burstBuf=Filename, .A=Device, .X=FilenameLen
Display the prompt.
.%219! ldx #0
.%220! - lda promptMsg,x
.%221! beq +
.%222! jsr kernelChrout
.%223! inx
.%224! bne -
Get the input line from the user.
.%225! + ldx #0
.%226! - jsr kernelChrin
.%227! sta burstBuf,x
.%228! cmp #13
.%229! beq +
.%230! inx
.%231! bne -
.%232! + jsr kernelChrout
Extract the device number from the start of the input line. If it is not
there, assume device number 8.
.%233! lda #8
.%234! cpx #2
.%235! bcc filenameExit
.%236! ldy burstBuf+1
.%237! cpy #":"
.%238! bne filenameExit
.%239! sec
.%240! lda burstBuf
.%241! sbc #"a"-8
.%242! tay
If a device name was present, then we have to move the rest of the filename
back over it now that we've extracted it.
.%243! ldx #0
.%244! - lda burstBuf+2,x
.%245! sta burstBuf,x
.%246! cmp #13
.%247! beq +
.%248! inx
.%249! bne -
.%250! + tya
.%251! filenameExit = *
.%252! rts
.%253!
.%254! promptMsg = *
.%255! .asc "enter filename in form filename, or a:filename, "
.%256! .asc "or b:filename, ..."
.%257! .byte 13
.%258! .asc "where 'a' is for device 8, 'b' is for device 9, ..."
.%259! .byte 13,0
.%260!
Scan the burst buffer after reading a sector into it.
.%261! wcScanBuffer = *
.%262! ldy #0
.%263! cpy burstBufCount
.%264! bne +
.%265! rts
.%266! + ldx wcInWord
.%267! - lda burstBuf,y
.%268! ; jsr kernelChrout ;uncomment this line to echo the data read
.%269! cmp #13
.%270! bne +
If the current character is a carriage return, then increment the line count.
.%271! inc wcLines
.%272! bne +
.%273! inc wcLines+1
.%274! bne +
.%275! inc wcLines+2
If the character is a TAB, SPACE, or a RETURN, then it is a Delimiter;
otherwise, it is considered a Letter.
.%276! + cmp #33
.%277! bcs isLetter
.%278! cmp #" "
.%279! beq isDelimiter
.%280! cmp #13
.%281! beq isDelimiter
.%282! cmp #9
.%283! beq isDelimiter
.%284!
.%285! isLetter = *
If the character is a Letter and the previous one was a Delimiter, then
increment the word count.
.%286! cpx #1
.%287! beq scanCont
.%288! ldx #1
.%289! inc wcWords
.%290! bne scanCont
.%291! inc wcWords+1
.%292! bne scanCont
.%293! inc wcWords+2
.%294! jmp scanCont
.%295!
.%296! isDelimiter = *
.%297! ldx #0
.%298!
.%299! scanCont = *
.%300! iny
.%301! cpy burstBufCount
.%302! bcc -
Add the number of bytes in the burst buffer to the total byte count for the
file.
.%303! clc
.%304! lda wcBytes
.%305! adc burstBufCount
.%306! sta wcBytes
.%307! bcc +
.%308! inc wcBytes+1
.%309! bne +
.%310! inc wcBytes+2
.%311! + stx wcInWord
.%312! rts
.%313!
Report the number of lines, words, and bytes read. Uses a "printf" type of
scheme.
.%314! wcReport = *
.%315! ldx #0
.%316! - lda reportMsg,x
.%317! beq reportExit
.%318! cmp #13
.%319! bcs +
.%320! stx 14
.%321! tax
.%322! lda 2,x
.%323! sta 15
.%324! lda 0,x
.%325! ldy 1,x
.%326! ldx 15
.%327! jsr putnum
.%328! ldx 14
.%329! jmp reportCont
.%330! + jsr kernelChrout
.%331! reportCont = *
.%332! inx
.%333! bne -
.%334! reportExit = *
.%335! rts
.%336!
.%337! reportMsg = *
.%338! .byte 13
.%339! .asc "lines="
.%340! .byte wcLines
.%341! .asc ", words="
.%342! .byte wcWords
.%343! .asc ", chars="
.%344! .byte wcBytes,27
.%345! .asc "q"
.%346! .byte 13,0
.%347!
Reports the error number given in the .A register. Called after an error is
returned from a burst routine.
.%348! reportError = * ;( .A=errNum )
.%349! pha
.%350! ldx #0
.%351! - lda errorMsg,x
.%352! beq +
.%353! jsr kernelChrout
.%354! inx
.%355! bne -
.%356! + pla
.%357! ldy #0
.%358! ldx #0
.%359! jsr putnum
.%360! lda #13
.%361! jsr kernelChrout
.%362! rts
.%363!
.%364! errorMsg = *
.%365! .asc "*** i/o error #"
.%366! .byte 0
.%367!
.%368! ;==========library==========
.%369!
Routine to print out the 24-bit number given in .AYX.
.%370! libwork = $60
.%371! itoaBin = libwork
.%372! itoaBcd = libwork+3
.%373! itoaFlag = libwork+7
.%374!
.%375! putnum = *
Initialize binary and BCD (Binary Coded Decimal) representations of number.
.%376! sta itoaBin+0
.%377! sty itoaBin+1
.%378! stx itoaBin+2
.%379! ldx #3
.%380! lda #0
.%381! - sta itoaBcd,x
.%382! dex
.%383! bpl -
.%384! sta itoaFlag
.%385! ldy #24
.%386! sed
.%387!
Rotate each bit out of the binary number and then multiply the BCD number by
two and add the bit in. Effectively, we are shifting the bits out of the
binary number and into the BCD representation of the number.
.%388! itoaNextBit = *
.%389! asl itoaBin+0
.%390! rol itoaBin+1
.%391! rol itoaBin+2
.%392! ldx #3
.%393! - lda itoaBcd,x
.%394! adc itoaBcd,x
.%395! sta itoaBcd,x
.%396! dex
.%397! bpl -
.%398! dey
.%399! bne itoaNextBit
.%400! cld
Take the BCD bytes and spit out the two digits they contain.
.%401! ldx #0
.%402! ldy #0
.%403! - lda itoaBcd,x
.%404! jsr itoaPutHex
.%405! inx
.%406! cpx #4
.%407! bcc -
.%408! rts
.%409!
.%410! itoaPutHex = *
.%411! pha
.%412! lsr
.%413! lsr
.%414! lsr
.%415! lsr
.%416! jsr itoaPutDigit
.%417! pla
.%418! and #$0f
.%419!
Print out the individual digits of the number. If the current digit is zero
and all digits so far have been zero, then don't output anything, unless it is
the last digit of the number.
.%420! itoaPutDigit = *
.%421! cmp itoaFlag
.%422! bne +
.%423! cpy #7
.%424! bcc itoaPutDigitExit
.%425! + ora #$30
.%426! sta itoaFlag
.%427! jsr kernelChrout
.%428! itoaPutDigitExit = *
.%429! iny
.%430! rts
5. UUENCODED PROGRAM
Here is the binary executable in uuencoded form. The CRC32 of it is
3676144922. LOAD and RUN it like a regular BASIC program.
begin 640 wc
M`1P<'`H`GB`W,C`P(#H@CR`V-3`R(%!/5T52(0``````3!$=AO](K1P**;^-
M'`JI`(60:""Q_R20$`<@KO^I!3A@J6\@D_^I52"H_R20,.NI,""H_ZF?(*C_
MH`"Y``L@J/_(Q/^0]2"N_ZT<"BE`T`0XJ0I@>!@@1_\L#=RM`-U)$(T`W2"]
M'*7^R0*0!=`$.*D$8,D?T"&D_Z("J0@L#=SP^ZT`W4D0C0#=K0S<F0`+R,K0
MYX3_&&!8.`D08*D(+`W<\/NM`-U)$(T`W:T,W(7^HO[)`I`6R1_0W:D(+`W<
M\/NN#-RM`-U)$(T`W8;_H`"M`-U)$*JI""P-W/#[C@#=K0S<F0`+R,3_T.48
M8%@88*D.C0#_(#T=($D=(",<D`0@H!Y@(`4>I?[)'_`((+T<D/(@H!X@#AT@
M6QY@J0"B")4#RA#[A0)@H@"]C1WP!B#2_^C0]:(`(,__G0`+R0WP`^C0\R#2
MLZD(X`*0'JP!"\`ZT!<XK0`+Z3FHH@"]`@N=``O)#?`#Z-#SF&!%3E1%4B!&
M24Q%3D%-12!)3B!&3U)-($9)3$5.04U%+"!/4B!!.D9)3$5.04U%+"!/4B!"
M.D9)3$5.04U%+"`N+BX-5TA%4D4@)T$G($E3($9/4B!$159)0T4@."P@)T(G
M($E3($9/4B!$159)0T4@.2P@+BXN#0"@`,3_T`%@I@*Y``O)#=`*Y@/0!N8$
MT`+F!<DAL`S)(/`;R0WP%\D)\!/@`?`1H@'F!M`+Y@?0!^8(3$0>H@#(Q/^0
MQ1BE"67_A0F0!N8*T`+F"X8"8*(`O8(>\!_)#;`5A@ZJM0*%#[4`M`&F#R#,
M'J8.3'X>(-+_Z-#<8`U,24Y%4ST#+"!73U)$4ST&+"!#2$%24ST)&U$-`$BB
M`+V\'O`&(-+_Z-#U:*``H@`@S!ZI#2#2_V`J*BH@22]/($524D]2(",`A6"$
M889BH@.I`)5CRA#[A6>@&/@&8"9A)F*B`[5C=6.58\H0]XC0[-BB`*``M6,@
D!!_HX`20]F!(2DI*2B`/'V@I#\5GT`3`!Y`'"3"%9R#2_\A@````
`
end
6. REFERENCES
[1] Commodore Business Machines, _Commodore_1571_Disk_Drive_User's_Guide_,
CBM, 1985.
[2] Rainer Ellinger, _1571_Internals_, Abacus Software, June 1986.
===============================================================================
Next Issue: (hopefully!)
Learning ML - Part 4
In the next issue we'll embark on a project of making a space invaders style
game for the C=64/128 using the KERNAL routines we've learned.
The Demo Corner: FLI - more color to the screen
All of us have heard complaints about the color constraints on C64.
FLI picture can have all of the 16 colors in one char position. What then
is this FLI and how it is done ?
The 1351 Mouse Demystified
An indepth look at how the 1351 mouse operates and how to access it within
your own ML programs. For Basic programmers, a driver for the 80 column screen
is also supplied.
LITTLE RED READER: MS-DOS file reader for the 128 and 1571/81 drives.
This article will present a package that reads MS-DOS files and the root
directory of MS-DOS disks. This package will use the dynamic memory allocation
package introduced in Hacking Issue #2 to allow large files to be read in.
The application-level code hasn't been finalized yet, but it will probably use
a menu-oriented full-screen display and will read and translate MS-DOS and
Commodore files.
=============================================================================
END of Commodore Hacking Issue 3.
=============================================================================
